Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
nrf master control panel android app sent only one byte, while sending more than one byte gives Error 13 (0xd): GATT INVALID ATTR LEN
cant we send more than one byte in...
Hi,
I'm gathering assembly specifications for a custom PCB that uses nRF5340. I don't find any specific recommended reflow profile and solder paste for assembly. I stumbled...
Hi,
Bit of a newb question but I am evaluating the Thingy 91 dev board and would like to also connect some sensors via the SPI interface. I was wondering what would be the...
Hi everyone,
I have one question just for confirmation. Can I supply the board from the VDD pins located on P1 header (Socket 1x8)? Shall I bear something in mind in that...
Hi,
We use nRF9160 and nRF Connect SDK in a device project.
Our customer have asked to declare all open soruce software modules and their licenses. Do you have such a...
Hi, I found one older question (7 months ago) with the same problem but that had no answer. Situation:
- SDK 15.3, s132 v6.1.1 - The softdevice has been enabled and ble...
Hello,
I want to add/enable logs in DFU secure bootloader exaple. For that, I have enabled following macros which are needed.
NRF_LOG_ENABLED, NRF_ATFIFO_CONFIG_LOG_ENABLED...
Dear
I am testing AGPS with my THINGY91
SIMCARD: TELIA /Norway
I got the output report:
Could you tell me what is the problem? Telia SIMCard?
Thanks,
BR
...
Hi ,
I use SES to build a project ,SDK version is 15.2.And get the err:unknown register name 'vfpcc' in asm.
This seems to happen with every file.For example :
and...
Hello all,
I am working on nRF52840 EVM board.
I am not changing any thing in nRF52840 EVM board.
I was using nRF52840 board for downloading firmware in external custom...
I'm trying to use an MMA8652FC accelerometer with the nRF52832. When I call the function nrf_drv_twi_tx() the board hard faults, stopping in <SDK>\components\libraries\util...
In the case that I used custom board, I used bootloader_secure to OTA; but after OTA, the program doesn't jump to the application, even app nrf connect notify Sent Successfully...
Dear Community;
I am running some current measurements on the NRF9160 DK. I am following the manual instructions:
1.-I am powering the NRF through external power supply...
Aim: transfer large data coming from UART to nRF52832 over BLE 5.0 as fast as possible. Want to use 921600 baud rate in the case given below.
Scenario:
SDK: 15.2.0 ...
I have created an out of tree board folder following the same pattern as the Nordic PCA10090 and that is working as expected. What I would like to do now is have 2 versions...
