Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi there,
I am having a hard time with some C pointers to add a new BLE Characteristic.
I would like to have a function that returns a simple characteristic metadata and...
Hi , I am using nrf52840 dk with zigbee cli example in sdk. I have configured nrf52840 as coordinator. I am using xbee pro s2c modules as router in zigbee network. Terminal...
Hi everyone,
I want to send my IMU's readings through BLE to a central. I have implemented the code and notify the central every 1s with the measurements.
I have an array...
Bonjour, je ne peux pas télécharger un firmware via l'application nfr toolbox avec mon Huawei p8 pour mon home trainer connecté, via bluetooth. Je reste bloqué à 2% et un...
I'm working on a solution and facing a few difficulties. well, I have more than 100 smartphones (android and iOS) devices in closed proximity were all the devices are logging...
Hi,
We have an embedded flash of 4Gbit which stores sensor data. The data needs to be transferred to a Smartphone. Now we are using USB cdc acm for transferring data with...
SDK 16.0
52810
S112
From the sample code of SDK we can see that the UART is enabled by code ourself, as the following. However, what's the usage of the NRFX_UARTE_ENABLED...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Please tell me the operation when garbage collection is executed. The setting values of FDS are shown below for reference.
We...
I am trying to program my custom board nrf52811 by pca10056 using ses, and i was able to flash any example of nrf_SDK, however the LED does not blink. even though i added...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
The following contents are described as the description of "FDS_VIRTUAL_PAGES". "One of the virtual pages is reserved by the system...
Hi, I'm trying do drive WS2812B LEDs (aka neopixels) with the I2S peripheral, using method similar to this https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/driving...
Hi,
I want to implement a Single Base UUID with 3 Custom Characteristics. I followed the instructions which are mentioned in the https://github.com/maidenone/custom_ble_service_example...
Hi,
I'm using the I2S for driving a Neopixel (WS2812b) , my code is working properly on the nrf52840DK . but when i flashed it to the adafruit nrf52840 board via the P19...
Hi,
Can you please provide a small UART application for the nRF52 and nRF52840, to communicate with PC application using bluetooth.
The deafult ble_peripheral applications...
I would like to connect an nRF52833 to a host through UART-over-USB. The host needs to be able to update the nRF52. HOWEVER, the host is itself an embedded device, not running...
