Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am developing a project where I have NRF52840 as a device and another NRF52840 as a BLE USB dongle connected to PC.
I have to improve the BLE data rate between the...
Hi,
I have a NRF52840 device connected by BLE to another NRF52840 BLE USB dongle connected throw USB to a PC application.
I want to synchronize the RTC on the connected...
Hello I am currently working on a project with the XM122 / XB122 kit for an evaluation, the XM122 card integrates an nrf52840 MCU and a radar sensor;
The goal of my project...
Hi, I'm using nrf52833 with SDK 17.0.0.
I want to send SAADC data over BLE.
So, I want to see data in my phone.
I've modified codes.
I want to use macro(ble_nus_data_code...
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/simple-application-level-authentication
Hi
I am looking to make this example work but this post is old...
Hi all,
we are now using nRF52811 and its SAADC. We would like to use the oversampling functionality, but there is some information missing in the datasheet.
So, when...
Hello,
nRF5SDk16.0, Softdevice v.7.0.1, device nRF52840.
We using manufacturer specific information in the advertisement data. Here are the set values:
The data is...
We have a PCB production with bug where AC13 (P0.18) accidently has a via shortenede to GND plane on internal layer. Thus nRESET is stuck low and cannot be pulled high without...
Hi,
I modified the LBS service to experiment sending more than a byte of data.
On the peripheral side, modified from ble_peripheral/ble_app_blinky
typedef struct { uint8_t...
I'm using visual code for my development. I've tested a basic hello world app, this works fine so c/cpp is correctly installed.
I'm now testing a basic app, but I'm getting...
Hi Team,
For our development we are using the nRF52840 soc, We need the some example code or some project which will explains the Usage of RSA algorithm and supported API...
Hello,
I am looking at the ble_app_buttonless_dfu/main.c
This implementation is initializing the queued write module. Is this required now for DFU operation? We currently...
Hello,
For some reason whenever I try to pip install pc-ble-driver it will only ever install version 0.11.4. This causes a problem since I need the nrfutil library and the...
I sent some nRF9160 prototypes down to a CTIA certified test lab in North Carolina to do carrier TRP and TIS testing. When they add their test sims they seem to be unable...
