Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hey everyone, I'm trying to use the QSPI module (again) to interface to RAM, not FLASH. I'm not really sure if this is possible, but we'll get there. Right now I can't get...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LETestEnd.
I tested with nRF51822 customer board...
Opening a project in SEGGER Embedded Studio I have annoying "no entry signs" (white minus sign in a red circle) on the left side various items in a project, whereas most of...
Working with nrf52832_mdk and using basic GPIO functionality, I am unable to toggle the GPIO pins P0.0 or P0.1. The code I am using is quite simple and I am able to toggle...
Hello,
I am working on the mqtt sample from ncs\nrf\samples\nrf9160\mqtt_simple. Mostly the nRF9160 connects to the MQTT server in the first attempt. But sometimes I observe...
Hello,
I work on nbiot evaluation and i try to send udp data from my basement.. I boot and attach network from ground-floor and when i'm on PSM mode im going on basement...
I want to run the board at 1.8V and run the uart and spi examples on my laptop. What should be my configurations and which micro-usb port shall I use to connect with laptop...
Hi,
I'm trying to send custom messages between server and client, based on the light switch example. I've modified button_event_handler and the client was able to receive...
Hi Nordic team,
I have an issue: I have to program/flash my mesh application together with softdevice140, mesh-bootloader and device settings page on the nrf52840 chip....
Hi everyone,
I am facing a kind of a strange problem. I want the system to enters system OFF mode when a certain pins goes to LOW. For that reason I have include code section...
I plan to use the nRF52833 or nRF52840 chip and as usual it needs a charger circuitry “PMIC” to charge the battery "Li-Ion"
Is there any special PMIC version recommended...
I'm using nRF52810 in a CR2032 battery powered device.
I use the DCDC mode to enhance power consuption. According to Product Specification in release 1.3 (and unlike nRF52840...
Hi,DevZone
I'm not Native English , sometimes can not express exactly, So, I'll provide a concise description about the question
1, platform: nRF52832_QFAA _E1, nRF5_SDK_13...
I used the NFR connect tool to install softdevice on the NRF52840 Dongle. I see noise about another tool to set up this kit in this forum; these are old. I forget what it...
