before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
The nRF52840 UART example uses pins 1.13 and 1.14 for the TX and RX pins on the Dev Kit (uart_pca10056) and has a default baud rate of 115200, but the 1.13 and 1.14 pins are...
Hi! I'm having issues with inconsistent battery readout results. I'll elaborate more below, but in general, I have multiple devices which 'sleep' most of the time, and when...
I have an issue when i am doing writing of a structure where autoprog is a struct like this :
typedef struct { uint8_t tag_tab[TAG_ID_LENGTH]; }tag;
typedef struct { uint8_t...
Installed nRFgo Studio lastest win64 verion nrfgostudiowin641212installer.msi and lastest windows 64 nRF-Command-Line-Tools_10_9_0_Installer_64.exe . But nRFgo does not work...
Hi!
I want to develop a simple program which count pulses in a digital pin in an interval of 10ms. I want to use a timer as a counter to count the pulses, also I want...
Hello Nordic Team,
We just received and test a new batch of SIMs using a nordic nRF9160. However, there is an error that doesn't allow to register these new SIMs. From LTE...
Hello,
we have a project on:
Periperal: experimental ble_app_blinky / and
Central: experimental ble_app_blinky c
We have add suplementary:
LEDBUTTON_LED4 ( BSP_BOARD_LED_3...
Hi,
I am unable to test current time service example.I followed all the steps mentioned to test CTS Example.But, below are the log messages:
Again if I try to reset...
I have an issue with my nrf9160 custom board.
I flashed successfully only 3 of 30 pieces batch. Other boards fail with "Failed to connect to target. No idcode detected"...
Hi !
I am working on aws_fota, with a nrf9160 dk, sdk 1.3.0. When I try to connect in mqtt, I get my IPv4 address I get the following message: ERROR - mqtt_connect...
Hello,
I'm trying to interface msp430fr5994 to nrf51822 as spi slave with soft device 110 and SDK v10. The master (msp40) sends 20 bytes to the slave (nrf51). The issue...
Hi,
I started debugging a device with an nRF52820 chip and found that the pinout is similar to nRF52833.
The test application was switching pin P0.15, but the ripple...
I'd like to order a debug in/out cable for the debugger (P18 & P19) on DK.
But I don't know what is the cable or the compatible sockets.
please let us know what is the...
