I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
It is possible to provision the NetKey, AppKey and unicast address of a node using the serial protocol, using the following messages:
Mesh Subnet Add, Opcode: 0x92 - NetKey...
Dear Sir or Madam,
It´s the second time, I got the same error while start developing with nrf52833 demo board. For first step, I flashed a blinky example to the board -...
Now I'm trying to change a device name in `nrf_dfu_ble.c`. I set NRF_DFU_BLE_ADV_NAME like following.
And I imported `stdio.h`, `string.h`. And I edited `gap_params_init...
Hi,
im trying to flash a 3rd party demo board (MDBT50Q-512K Module Demo Board) with nrf connect for desktop. As programmer I use original Segger j-link edu mini.
As...
Dear Nordic:
My peripheral is configured to use MTU 247.
When connected by NrfConnect of IOS, I can receive NRF_BLE_GATT_EVT_ATT_MTU_UPDATED event and check the effecitve...
We are designing in the 52840 as a processor in a new sensor product and are looking at using the HOLYIOT YJ-18010-nRF52840 part that you indicate on your site is a third...
Env setup:
nrf52840 on PCA10056, SDK 16.0.0, S140, FreeRTOS, secure bootloader
Description:
I'm trying BLE background DFU in the application.
Had reference iot/background...
Hi
Is there any implementatiaon of nrfutil, and more specifically the DFU via serial port, as a C library? My use-case is I need to update an nRF52840 from within an already...
Hi,
I am able to set up uart async receive, but when I try to set the call back using uart_callback_set() so that i can call the uart_tx() routine to push the data out,...
Hello,
I am working on nRF9160DK. I am using SES for ARM (Nordic edition).
How can I import new libraries for any project? Let's say I want to import SD card libraries...
Hi!
A little backstory on my project: Currently I have merged the saadc and peripheral ble_app_uart example. The value from a potentiometer is then sent over ble to the...
Hi,
I'm developing a project with nrf52832 sdk 16.0.0. I have some issue about the fds. peer_manager had used the fds modul, as we knew. And I would call fds_record_write...
I am looking at the APP_ERROR_CHECK and find out it finally goes to the app_error_save_and_stop method. I couldn't understand from the code, that where the error info saved...
