It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
i am begginer, using my nRF52832 DK with ble_app_uart as peripherial, which is connected to PC via J-link (usb cable). I want is to establish serial communication between...
Hi,
in DFU error occurred and showing as [DFU] Remote DFU error: Insufficient Resources in the log.
Chip Used NRF52810
package size is 53.8 KB
is there any restriction...
Hi,
I just got a ppk2 and I am not sure which wire needs to be connected to where.
I am going to use this to measure current consumption but I've used only extarnal DUT...
Hi all,
I'm starting a project with a nRF52840, and start protoyping with pca10056 board.
I started with compiling ble_app_blinky example app, with armgcc.
I can compile...
My nRF52 device has a connection opened in peripheral mode and in some cases I want to close the connection with reason code "power off", i.e. call sd_ble_gap_disconnect with...
Hi,
I'm reading through the documentation on using the SAADC with the NRF52 kits. The examples are using PPI to manage the SAADC and allow it to sample locationally in...
Dear All,
I need a high frequency clock in order to measure the time between a couple of events. In the RTC HAL there are functions that allow to retrieve the counter...
nordic nrfconnect sdk, wrong bit mask in driver for thingy light sensor bh1749
In the nordic nrfconnect sdk there is a bitmask typo causing wrong anction.
The header...
When running firmware without a probe, interrupts don't seem to work. I'm using a Segger Mini Edu on an Actinius Icarus (nRF9160). I'm using EGU1. When the probe is attached...
Hi,
I am looking for detailed electrical characterization details for SAADC - beyond 1 page summary in nRF52833 product spec v1.3; under 6.21.10.1 SAADC electrical specification...
Is there some documentation listing what C library functions are supported? For example if I use the Keil IDE to look for FILE I find it. But if I look for 'fread' it says...
Hi,
I'm building a gateway using nrf mesh serial, and I want to monitoring devices status in the network by listening heartbeat messages from devices, but when I set publication...
Dear All, We will do a production with over 1000 Nordic nrf9160 devices, for which we need to program the modem firmware (v1.2.0) and the application software. We would like...
Hello, I started learning BLE/nrf about a week ago and I faced an issue that I unable to handle more than one connection simultaneously.
I have a pretty simple application...
