I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
Here, i have using two I2C functions EEPROM + SENSOR with nRF52832.
Initially, using ble_app_uart example to read Sensor data using TWIM.
Every minute read Sensor...
I started with ncs/nrf/samples/nrf9160/lte_ble_gateway and have taken parts of ncs/zephyr/samples/subsys/fs/fat_fs to get SD card support
prj.conf
CONFIG_NEWLIB_LIBC...
Here are some of the issues which I am facing in SEGGER Embedded Studio since I updated to nRF Connect SDK v1.3.0:
After I press Debug, Go, a dialogue box opens asking...
I am using NCS 1.3.0. I try to build mcuboot with CONFIG_PM_SINGLE_IMAGE=y and it looks like partition manager is never run. I do not get any partitions.yml output in my build...
The serial_lte_modem sample is heavily broken. Unlike the AT client sample which simply works with PuTTY out of the box, for the serial_lte_modem you need to configure PuTTY...
Hi all:
I am using sdk 16.0.When put system on idle mode call two times sd_app_evt_wait it works well.But I want to save power,so before enter idle mode,but when I call...
Hi despite trying 3 different approaches (even using the Nordic driver lis2dh12 on a blinky-based project and installing Segger Studio to step/debug into the library code...
I wish to send a message from the nRF Cloud terminal to my device that will land in this branch of nrf/applications/asset_tracker/src/main.c.
} else if ((cmd->channel =...
We have a custom radio protocol that manipulates the radio registers directly (on the '32) and I'm evaluating whether or not we can switch to the '33 to use it's angle of...
i have used a example of ble_app_template in ble_peripheral of SDK15.0,when code run in ble_advertising_start,return errcode 8.
i have checked low speed Crystals，it's ok...
I get error 0x3401 in ble_app_uart_pca10040_s132 (nrf52 dk, sdk17) in ble_nus.c line 95:
err_code = sd_ble_gatts_value_get(p_ble_evt->evt.gap_evt.conn_handle, p_nus->tx_handles...
Hi,
I've been using the python bindings for the pc-ble-driver and have been getting things to work, but I noticed there is no API exposed for reading the RSSI of a connected...
I am using nrf52811, SEGGER Embedded Studio and I want to use Beacon demo. I click Build and Run , it prints as below:
And I can not find the beacon device in nRF Connect...
Hello,
We are planning to buy the BWG840F BLE to Wi-Fi gateway.
https://www.fanstel.com/wifi-ble-5-iot-gateway
It has the nRF52840 module (BT840). We have the nRF52833...
Environment:
Segger Embedded Studio
nRF52840
S140
Windows
nRF 5 SDK 17
Hi,
I'm developing a device for a small side project. I need to get logs in both the...
