I am trying to run the debugger from the nrfconnect extention for viual studio code. for some reason It doesnt work, It seems to flash the app fine, but then this message...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
I am using 2 nRF528400DK boards. Each board has a unique BLE Mesh sample loaded. The samples were made by modifying the default mesh sample provided by zephyr. One sample...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
hi... i want to store data in flash , i will get the data periodically . Even i am writing data to flash using write command ,when i am trying to print the data which is stored...
I am using nRF52 DK.
When I do 2 analog inputs using the SAADC, I noticed that, in the SAADC callback, p_event->data.done.p_buffer[0] corresponds to the correct SAADC channel...
Hello,
I use a configuration with multiple NUS_C and NUS links. When I receive events, how to know the index ?
I have seen mutiple exemples using conn_handle but in a...
Hi teams,
I am trying to automate preferred mesh configuration for each node.
For example, if I use nRFMesh app, I should 1) bind application key to each model, 2) set...
Hi everyone,
During test with my small mesh network, I found that adding all-nodes to subscription list is prohibited by Mesh Specification.
In Mesh Profile 4.3.2.19,...
Hi:
I use the sdk https://github.com/jimmywong2003 to make a bin file and then run the command of ./UartSecureDFU ttyACM0 application.zip to updgrade in linux
It always...
Hi
if one searches the examples using the timeslot API, every application seems to do it's own timeslot cleanup. Also documentation is not very clear about this.
Best...
i am using nrf52840 dongle with uart using ble_app_interactive example,
but after commenting only uart with cli is replying with some text as shown in image .
For the...
Hi! I'm using S140 and I'm using the ble_advertising module to set up advertising.
This is my advertising_init function which is working properly until I uncomment the enabling...
This is perhaps not so much a question as a request.
The FDS event handler, type `fds_cb_t`, has only one argument, type `fds_evt_t`, unlike (say) the two wire event handler...
Hello,
I would like someone to explain to me payload for Zigbee cluster library (Zcl)
i was following this guide to control my lights:
https://infocenter.nordicsemi...
I am trying to connect to another type of board via the UART on the development kit. However, there seems to be a voltage mismatch. Are the nRF52840 development kit UART signals...
hi... i want to store data in flash , i will get the data periodically . i have merged the ble_app_uart +fstorage example . Even i am writing data to flash using write command...
Hi everyone, I have a question related to the power supply of nRF52840 DK
I want to operate the nRF52840 DK with a LiPo battery (for experimental purposes). Is it possible...
