I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hello,
This is first time to design the PCB antenna for nRF52840 BLE Chip. Can i use the nRF52840 DK Board HW layout for reference or should i use the USB dongle for nRF52840...
SDK16
S132
nrf52832
SES / Windows 10
After much searching this site and the web in general I'm reaching out for support.
While in low-power mode I'm seeing a pulse...
Hello im an Android developer and we have an app that uses an older library but still works with are older products.
we currently use
implementation 'no.nordicsemi.android...
From what I read on DevZone it seems that there is a limitation in nrfutil when needed to update BL+SD+APP. NRFConnect over BLE manages the 2 separate downloads (BL+SD and...
Hello there The problem I encountered was that when getting the slave service, returning to get the service failed. I used DEBUG to check the p_ble_gattc_evt->gatt_status...
Hi,
I am using nrf Connect SDK v1.2.0 in Segger Embedded Studio 4.52 and developing on a nrf52840 development kit (pca_10056). I use the "configure nrf connect sdk project...
My goal is to establish a BLE connection between the DK and the smartphone, using NFC for the OOB pairing . I am using the nRF52 DK and the nRF5 SDK , v.16.0.0.
The intended...
Hi,
I am having issues with getting SPI up and running on my nrf52840-DK using NCS. I've tried getting support about this in another ticket but it seems like it lead to...
Hi,
We are using the nRF52840 SoC.
The following image is taken from the datasheet:
It shows a Gain block before the SAR core
a. Does the Gain block serve also...
Hi ,
I want to know if it is possible to close/open the uart connection with RTS and CTS pin in order to have a low power UART?
When RTS and CTS are high, uart is closed...
Hi,
Can any Zigbee application receive ieee radio interrupts in both TX and RX path?
What I need is:
In the case of Zigbee Tx, an advance notification of 200 μs would...
Hello, I am using nRF52 DK and softdevice s112, developing with SDK V15.2. I am exploring the fds library and have encountered some strange behavior. When I connect the nRF52...
Hello,
I am using nRF52840, S140 v7.0.1. We want to measure distance between two nRF52840 with BLE 1 Mbps and 0 dBm.
I am referring below two links.
In this its...
Hi,
We have 2 microcontroller on board. One of our micro controller will update nordic chip using serial DFU without any signed keys.
For testing purpose i am implementing...
