Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hi... i am using nRF52832 ,15.2 version sdk . I want to send the data from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can able to transmit the...
Hello,
I'm trying to setup an automated pairing for two devices. My peripheral device is advertising and should only allow connection requests from a specific central device...
I'm developing a multirole device to connect to a peripheral device that we developed earlier.
The multirole device when acting as a central device it scans for the peripheral...
To the kind attention of Nordic support team,
1. I have been using secured gazell library, where master is always polling in order to receive a message.
I was wondering...
Hi!
I'm developing a TCP server running on th e nRF9160, but there seem to be a problem with accepting clients. The code is very simple, just calls to socket, bind, listen...
Hi. I've developed a PCB with nRF52832 and I'm having problems with the circuit. When I put my hands closelly of P0.00(XL1) and P0.01(XL2) the bahavior of nRF changes... I...
I apologize if this was already answered elsewhere - I didn't find it.
I have been digging in the nRF52840 source code for the serial_nRF52840 SES project to understand...
Hello, I am trying to switch from BLE_GAP_PHY_AUTO to BLE_GAP_PHY_CODED in runtime, and I need to change central event length via sd_ble_cfg_set(). Whether is it possible...
Hi, i am working on servo motor using nrf52840 development kit , i want to run parallely four servo motors , i have merged the ble_app_uart+pwm library example ,
1. As of...
Hi,
I am using an external RCT module to provide 32.768kHz square wave for the nRF52832 instead of an external crystal oscillator. When the system goes to deep sleep mode...
Hello,
I'm aiming for flashing the nrf52832 via SWD via my own SWD implementation.
I'm good so far with the init phase, reading IDCODE writing registers. Long stort short...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I modified ble_app_blinky with below...
I am getting ecg data from max30003 IC which i want to send via BLE to and application. I have the Ble code working on its own and the SPI code to get ecg data working on...
Hi,
I am working on nRF52840 (dongle) using nRF Connect for desktop on windows 7.
I was able to write the "peripheral/blinky" example and was able to see the output...
