Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
Hello
I'm going to use a potentiometer to control the pwm. I am using a 10K potentiometer and have used a saadc example.
I printed out the value of adc through this example...
Hi everyone,
I've just been working with NRF52833 and nRF5 SDK for Thread and Zigbee v4.1.0 to create a zigbee mesh network for home automation. My network is pretty simple...
Dear Members,
I saw this code ,
If there is no input, how can I handle it and display result = 0 and not shutting down CPU ?
How can I display 0 from this code...
Hi.
I want to disable the TWI master's internal pull-ups on SCL and SDA. So I set it according to the contents of the following URL, but the setting is not reflected as...
Dear Nordic Support team,
Currently I am in the process of adding the USBD_CDC_ACM driver code to our existing application following your usbd_ble_uart example. I can receive...
Hi，
Our customer is using nrf9160.There is a problem about powem_on circuit .
Attach is the schematic diagram:
Here VBAT is 4V,PW_ON is connecting to the nrf9160...
Hi,
I'm using nRF52810.
And i'm trying to measure battery level using saadc.
The problem is saadc result is not accuracy.
When battery voltage is 3.3v, saadc value...
Have a brand new Thingy 91, latest modem firmware and asset tracker firmware: thingy91_debug_ltem_2020-10-30_5522ca2b.hex.
But within the LTE monitor app, nothing shows...
For the nRF52811 there is only one TWI peripheral and if there are multiple buses required it is necessary to remap the SCL and SDA pins to the peripheral. In the nRF5 SDK...
I am migrating to the Fanstel BT840XE module with nRF52840 and a Skyworks PA/LNA. I need some assistance in getting my PA/LNA working in a multiprotocol setup.
I have successfully...
I have application developed that works ok on nRF52 DK (nRF52832) with S112 and now want to migrate it to a custom board with nRF52840.
Could you confirm that S113 is...
Hi:
Since we have a issue that when nRF52840 setting to DCDC mode, our inductive touch will have bigger noise, if setting to LDO mode, the inductive touch noise disappear...
Hi,
I've been trying any way I can think of to work around an issue "51" returned by nrfjprog executed from nrfutil when trying to run serwer from the steps in tutorial...
