Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
HI
I am using the customized nRF52832 board with a temperature sensor connected via i2c .Firmware i merged the ble_app_uart and twi_sensor xample code. Here the RX AND SDA...
Hi everyone,
I've written a custom BLE service with two characteristics. I want to write more that one bytes to one of the characteristics and then to store the written...
Hello,
I'm working with nRF52840 and SDK v15.2.
I implemented an USB layer with CDC and MSC classes based on nRF examples. All seems to work fine. The USB Serial port...
Hi,
I am using TPS61021DSG in my design which is a data acquisition system using nRF52832 BLE module. I am using 1.4V Zinc-air battery to power up my circuit to generate...
Hi Nordic Team
I want to run the example project[802_15_4] on the soc chip 52820.So for the SDK17.0,it run and work well on soc chip 52840.
In order to run on the chip...
Hi,
I am using an Adafruit nrf52840 Feather board and have been having a problem with SPIM instance # 3.
I have the board connected to a display module and have been successful...
Hi,
This is not a ticket!
This is a project that I built. It uses the nRF52 to control a neopixel (ws2812b) via I2S over BLE using a custom mobile app built using the...
On SDK16.0.0 + Mesh SDK 4.1.0
I know that oversampling when using the SADDC in scan mode on multiple channels does not work because the buffer gets all out of order.
But...
Hi,
as describe in the title, we are getting a mesh assert when trying to remove all suscibtions from a model.
it is kind of hard to reproduce because this command is...
Hello,
I am testing direction finding over nRF5340 PDK.
I didn't have antenna array yet, but I think that's equivalent to signal received at 90 degree.
I have two questions...
Hi,
in SDK/components/libraries/timer/drv_rtc.h, there is some preprocessor define provided to select the RTC module (0, 1 or 2) used by app_timer2: APP_TIMER_V2_RTC0_ENABLED...
I want to trying to the HCI Command (DTM Mode) of CTE (Constant Tone Extension) feature for SIG RF Pre-TEST,
The nRF5 SDK v16.0.0 (latest version) is ready for CTE feature...
Hello,
So I am trying to build the ble_app_blinky_c example of SDK_14.2 to work for nRF52810 but encountered problems.
I used s132 v 5.1 for my softdevice by following...
Hi,
We have a project want to fixed "access address".
We want to fixed "access address" in every BLE connection (52840 as master)
Do you have some of API to assign ...
Hello, i made my own working NRF24L01+ using the reference design from the datasheet and it worked quite well. But i needed some more range so i wanted to add PA+LNA module...
