I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello:
I am porting the LESC with MITM security protocol from your "ble_app_multirole_lesc" example inyo a project that runs FreeRTOS. This is on an NRF32540 With s140...
Hi,
I'm using an nrf52840 dk to query another device over spi and then pipe the response back USB to a host PC. Ideally, we're piping data at 1 Mbps (which should be very...
Hi,
We are using nRF9160 DK. Loaded the asset tracking application, and followed all the procedure to connect to nRF cloud.
In nRF cloud i can see the data in the cloud...
Hello,
I am currently designing a custom PCB with the nRF8001 chip. For a smoother assembly and component procurement, I am looking to make all the resistors on the board...
Hi there,
I have a problem with the bootloader from the RF5_SDK_11.0.0_89a8197 together with Intel Wireless Bluetooth chipset.
I use the softdevice s132_nrf52_2.0..1. I have...
Hi im after the library driver for the nRF509 using Arduino but when i go to the webpage to get it the webpage says not available can someone advise please
Many thanks ...
Hello,
Is it correct, that periodic advertising is working only with non-connectable mode? To implement periodic advertising with connected mode I need to start the second...
Hi, I tested a simple client-server UDP application, using as a template the UDP examples from the SDK. The UDP server is running in a nRF52 board and the client is a Python...
Hi,
my goal is to send data to the Google Cloud Platform using CoAP.
I found this example:
https://infocenter.nordicsemi.com/topic/sdk_tz_v3.1.0/thread_google_iot_coap...
Hi,
Recently I have been working on nrf9160 and wanted it to work as a modem for a linux computer for example raspberry pi. The aim here is that I connect the nrf9160 to...
Hi,
We are using nRF9160 DK. On the Arduino connector, we connected STM X-Nucleo-IKS01A2 sensor shield. We wanted to fetch the sensor values using nRF9160.
What example...
Dear Sirs, good night
Currently developing hardware using nRF52840 based module (BT840X from Fanstel)
Wanted to ask if following assignment would be OK for controlling...
I would like to know What is the limit on the number of ble devices that can be tracked concurrently by one Nrf52833 acting as an AoA device?.
Is there any reference antenna...
When I migrated the official routine pwr_mgmt, the following warning occurred after the compilation was complete. The files were all the same, but why didn't the official...
