This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I am going to find out an ideal throughput of NRF52832. And my environment is NRF52832/S332/MTU 247/connect interval 20ms.
Finally, i got a maximum value about 23Kb/s. I...
I have a nRF52840-PCA10059 dongle.
I have a PCA10040 dev boeard on which I programmed the ble_app_hrs_freertos_pca10040_s132 example after I modified HEART_RATE_MEAS_INTERVAL...
Hi,
I have some code which is based on the ble_app_gatts_c example sdk 15. I am using a Nordic NRF52840-dk pca10056 s140. Coding in Segger.
I want to each second change...
Hi,
I want to set the unused pins to low Level, however without using Software to do so, i.e. this has to be done before the chip is turned on.
How can I do that? Is...
Hello all, I have a little problem.
I`m trying to do an gateway communication using my NRF9160. The routine I`m trying to accomplish is next : -- Send message over serial...
Hi... i am getting the data through the RX,TX which is externally connected to the nRF52832 development kit , now i want to store the continous incoming data to the variable...
Hello, I am using nrf52840 board and SDK 16.0.0.
I am trying to merge this calendar example ( https://github.com/NordicPlayground/nrf5-calendar-example ) into ble_app_template...
1. I am trying to test the QSPI flash performance in nrf52840_DK ,but the QSPI init failed because of the event ready check,can i turn off the event check process?
2. I...
The recommended circuit in the v0.5 nRF5340 product spec differs a little from the nRF5340-PDK and I'm trying to understand the minimum requirements for an antenna. The spec...
Hi everyone, I am a beginner with the nRF52840 and I am looking at the example spi_pca10056 on SDK 16.0.0. What I've noticed is that at sdk_config.h file the pin configuration...
I have a question about what functionality is handled in the modem firmware vs. the application firmware.
I see from the nRF Connect SDK that the nRF9160 application communicates...
I'm using segger IDE for EVK-NINA-B1. I've downloaded nRF5_SDK_16.0.0 and trying yo run one of its example but getting error like stray '#' in program. I've attached 2 pictures...
Hi,
I'm using NRF52832 SDK15.2 to develop a smart band. Each time reconnect with iphone, the application assert in the peer manager event handler pm_evt_handler().
Any...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
