Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
hi,
I am using nrf52840 (in a Laird module) and trying to advertise such that legacy BLE 4 mobile devices can connect. Only BLE 5 mobile can see the device (running nRFConnect...
Hi, I have a problem with the reset pin not working on the nrf52811. The firmware was developed on the nrf52840dk board and now that we are migrating to the real nrf52811...
Hello,
I have one SPI instance (instance 3, but have tried others) reading data from an ADC. It's reading data from an ADC triggered by a DRDY signal at 25khz. I setup a...
Hi,
I just enabled the CONFIG_BOOTLOADER_MCUBOOT=y for serial LTE modem application to understand the flash partitions and to perform the serial DFU(not sure if its really...
Hallo, using nRF52840 DK with Keil uVision 5.30, I try to debug the example ble_app_uart in the folder ble_peripheral, pca10056, s140. Compilation is OK, erase/programming...
please help me
I was working with LPCOMP when I set up lpcomp like above, even though I have set my comparator but just impacting anything on the AIN2 pin...
Hi,
I am using nrf52832 mesh board.I want to unprovision the device by pressing the button on the board.In the lc server example they handled it in rtt as it dont have hal...
Hello everyone, I am Smit and I am an IOS developer.
I am stuck to write data into the BLE device. Can anyone please help me out with this? Can anyone tell me how to do...
Hi,
I used the command line to install the toolchains as follows:
sudo apt install gcc-arm-none-eabi
It then installed version 9.3.1 of the tools on my Linux ubuntu...
Hi,
We have implemented a custom Watchdog Timeout handler, where we do the stack-dump. It has worked fine and we were able to analyze and fix the Watchdog resets. But...
Hi,
We are using some nRF52 DKs for debugging and programming prototype boards. Everything went fine until we wanted to expand our testing setup and got some new nRF52...
Hello team, I want to use Normal Sleep mode that is (__WFE) normal sleep mode in NRF51822 using MBED OS 2. But, when ever I am using this method, my code has been waiting...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
The following vulnerability "CVE-2020-10135" has been reported by the Bluetooth SIG. Will this device be affected...
Hello
I am using SDK v17 and sending the value of acceleration sensor to the app.
I want to use this value to process some action in the app. For example, if the transmitted...
