Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hi All:
Not called the above timeslot, peripheral timer( nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(2) ) Can enter timer_handler normally. code snippet:
void...
Hi All:
Not called the above timeslot, peripheral timer( nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(2) ) Can enter timer_handler normally. code snippet:
void timer_handler...
NRF5 SDK 15.3.0 has an issue in a module nrfx_wdt.c . In function nrfx_wdt_init line of code: nrf_wdt_reload_value_set((p_config->reload_value * 32768) / 1000); causes to...
I managed, through the Nordic library for Android `thingylib` ([github]( github.com/.../thingylib)) , to connect to thingy52 and receive in the callback listener `ThingyListener...
I am following the example guide:
https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-connect-sdk-tutorial
however when I try...
Is there a guarantee that I can do something like: at+cfun=1;+cfun=44
and the nRF9160 will *not* start connecting to a tower? I would like to be able to interface with the...
Hi,
I have searched Devzone for changing the transmission power; even though there were similar issues related to mine but at the end, It did not help me.
I am evaluating...
Hello
I am reading sensor and broadcasting via nrf51DK its working perfectly when voltage supply is morethen 3v
but when I give voltage between 2.1v to 3v its stop broadcasting...
I cannot install the app "Programmer" automatically. The connection always fails due to poor network in our country. The error report is as follows:
Is there anyway to...
Hi Community,
printf() (and variants) fail on rounding floats: This is is probably an error in the printf implementation. I tested it with SDK 16.0 on NRF52840.
Format...
Hi,
In addition to listening the advertiser's and beacon data we also need to offer the master application - which is connected to BLE-module via UART - the possibility...
Questions about ‘Application data’ placement in the flash memory
Is there a function or other mean that could give me what is the lowest flash memory address that is occupied...
Hello All,
I am working on the Nrf52810 with sdk 15.3.
When we connect device through nrf connect app (android) i wanted to disconnect after 1 min .
I have given timer...
