i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I am having trouble modifying simple_hal.c from the mesh SDK v4.1 when buttons are on Port1 instead of Port0 on a nRF52840. I have buttons on P1.01 and P1.02.
Everything...
We're attempting to move from v1.1.0 to v1.2.0 of the NCS, in order to take advantage of some driver improvements (particularly DPD in the SPI NOR driver. When we migrate...
Hi,
I am currently working on a custom product that uses module BMD-300 from u-blox, which has nrf52382 chip in it. My application works fine and now I want to integrate...
hi,
Im developing a mesh network based on the nRF52832. I want to send some long message(over 11 byte) without segment, so I enabled the EXPERIMENTAL_INSTABURST_ENABLED...
I turn on the Instaburst feature already , after that , I program serial example to 2 nRF52832 and run it with interactive_pyaci
when i try to do PacketSend with 20 bytes...
I am running a Bme280 sensor with nrf9160 and getting this error msg ( [ 1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0 ) while getting the actual sensor...
Hi All,
Since I measured a very current consumption by testing CLI example (ftd/usb) I'd like to know how to switch my nRF52840 DK as Sleepy End Device.
Any suggestion...
I have a zephyr sample app running on a nrf51822. It's the onoff_level_lighting_vnd_app found in samples/boards/nrf/mesh. I have an iPhone running nrfMesh. I can't find documentation...
Hello, Im working with nrf52832 and sdk15 I'm working with the example: nRF5_SDK_15.0.0_a53641a/examples/ble_central_and_peripheral/experimental/ble_app_hrs_rscs_relay I want...
How can I receive all the packets from all addresses?
In the datasheet I see there's an RXADDRESS which setups the receiver to which address it will listen to. I want to...
I am using the zigbee sdk4.10 cli_agent_router and multi_sensor example. The 52840 module is E73-2G4M08S1C, antenna is a built-in ceramic antenna. During operation, the communication...
Hi,
I have central based on the 840 and a Peripheral on the 833 , I Need to ability to upgrade the peripheral version from the central.
I know that there is no example...
Hi All,
I am trying to use the RNG peripheral through the softdevice (i am using Version 5.0, with 14.2 SDK) with the sd_rand_... functions. I have enable d the RNG in...
i use the hex
sniffer_pca10056_129d2b3.hex
the packet is
nrf_sniffer_for_bluetooth_le_3.0.0_129d2b3.zip
my board is nrf52840- dk
but the wireshark only capture...
