hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I want to encrypt with AES-256.
I want to use the following two functions.
mbedtls_aes_setkey_enc mbedtls_aes_encrypt
I want to add a library containing ncs/v1.4.1/mbedtls...
Dear Support team,
I used PPK2 to test the PSM mode current of nRF9160 is about 7.09uA (as shown in the figure below),but the eDRX mode current has not been tested successfully...
Hello everyone,
I am going tp establish a mesh network by using a devkit and two or more dongle. take as an example, turning off a led on the dongle boards by using a bottom...
Hi, I'm using code based on sdk/components/libraries/bootloader/dfu/ for ECDSA verification of the signature. But switched to Oberon crypto backend. The signature was successfully...
Hi,
I'm trying to convert the NCS - cloud client sample to connect to AWS_IOT rather than NRF cloud.
After a connection achieved, i press Btn1 and I get the following...
I believe I am having a very similar issue to devzone.nordicsemi.com/.../dfu-from-external-flash-using-spi-nor
I posted this as a new thread to avoid high-jacking that one...
Hi everyone,
I am working on USB MSC example . I have two questions.
1. What is the MSC_WORKBUFFER_SIZE defines in the example? Is the last parameter of APP_USBD_MSC_GLOBAL_DEF...
My issue seems to be similar to DRGN-12539. However, I am erasing internal flash.
I am calling in a loop nrfx_nvmc_page_erase to erase multiple pages of flash. At first...
I am building a custom boot loader to work with out application on a custom board based on the UBLOX NINA-302 module. The boot loader will use USB as the only connection and...
Hi.
I'm trying to read data of MAX30102 using TWI, it has 8 bits of data in the FIFO_DATA register.
The library I'm using for data extraction and processing was written...
Hello,
I am using the nRF52 DK with Segger Embedded Studio and the SDK 14.2.0. I wanted to build the example 'esb_ptx_pca10040' with logging enabled. To achieve this, I...
Hi,
I'm using the S132 on the PCA10040 with the external XTAL disconnected (SB1 and SB2 cut)
In order to check to if the external is present I call nrf_sdh_enable_request...
