Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
I want to use external power (battery) and USB power together.
If USB is not connected, I want to supply it with battery power, and if USB is connected, I want to...
Dear HW engineer,
I have ordered a few custom boards with nRF52820. As recommended by the datasheet, I have used 12pF load capacitors for both HF (32MHz) and LF (32kHz)...
Hello
I use nrf52832 and SDK v17.
I'm conducting various tests on Bluetooth. And I faced a lot of new problems. I erased a previously saved bond from the Android nrf connect...
Hi
After successfully testing nRF9160 SLM app. we plan to use nRF9160 with UDP and LwM2M protocol in our smart devices. We also have our private cloud server where all the...
Im new using Nordic devices , I am trying to using nrf52840DK to locate nrf52840 dongles using the direction finding method , how can I connect the dongles to the DK and build...
HI,
Is it possible to update modem firmware from 1.2.0 straight to 1.2.2? Or is it the only way to first update from 1.2.0 to 1.2.1 and then to 1.2.2?
Regards, Tero
Hello
I'm testing the firmware using the BLE. When I upload, I can see that the board is working. Also, I don't think there's a problem with running each line of debugger...
I'm trying to build the blinky zephyr sample for nRF Connect SDK and get the following failure:
Creating solution blinky.emProject
/usr/local/bin/cmake -GNinja -DBOARD...
How can I, from the pc-ble-driver API, send an insufficient authentication request without configuring a characteristic to be secured?
I am testing out new standards. One...
Hello, Nordic community,
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Thanks,
...
Is there a limit to the number of handlers that can be registered using NRF_PWR_MGMT_HANDLER_REGISTER? I can't seem to get any more than 3 to be called, changing NRF_PWR_MGMT_CONFIG_HANDLER_PRIORITY_COUNT...
Hi--I'm part of a research group that will be using the Thingy 52 to record environmental variables, and we will need to transfer information to a cloud server using a satellite...
HI，ALL：
How to setup TX mode in example PRX，and so,how to setup Rx mode in PTX example. I use esb_init() of example PTX in example PRX， But when I fill data in fifo, it...
HI，ALL：
when using ESB example ,the transsmit waveform is below(in channel 3):
how to make it more simple,like that as below(other example in channel 3):
