I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hello
We are planning to build a product based on nrf52840 our programming part is almost done we used nrf52840Dk board , now we are order SoCs and other peripherals ...
May I know what is the difference of three PNs NRF51822-QFAA-R (H0) AND NRF51822-QFAA-R (G0) AND NRF51822-QFAA-R?
How to identy the three PNs? May I know if NRF51822-QFAA...
I am trying to implement a scenario where the system will be sleeping for a mentioned period of time and then wake up and advertise and transfer data over BLE.
I am using...
Again, if the search engine in your documentation were decent, I would probably not need to ask this question here. The answer probably exists, but try an find it not knowing...
Hello Nordic lovers,
Happy Merry Christmas.
In ble_uart code, I'm interfacing the FreeRTOS & twi_sensor code
The program executed without any error.
And it starts...
Dear Members,
How can I wake up the chip without a button
I'm using the example for Ant,
Ant_bsc_rx .
I have disabled the button with :
bsp_init(BSP_INIT_LEDS...
Hello and Merry Christmas,
Trying to get Thingy:91 connected to cloud. But no such luck.
Followed the video, but somethings are shown. Installed latest firmware (SIP modem...
Hello
I have two questions. Your thoughtful response will be appreciated.
1) What's the impact on power consumption with 1 Mbps vs 500 kbps vs 125 kbps for the same amount...
Is there any way to leave the PPK 2 output enabled when I leave the Power Profiler app? If not, then can I submit this as a feature request?
Without this option I have to...
1、Does Nordic 5340 support 1443a protocol；
2、When the chip（5340） is not powered, does NFC function support passive swiping card
3、Can the reading distance of NFC be more...
Hello
I am using the APII described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/modem_key_mgmt.html
to add keys to the modem...
Why does the nRF9160 Tx power fall far short of the specification? Its seem to be a false claim that the nRF9160 is a 23 dBm device, and rather is a 20 dBm device. In other...
In the flash write example code the very start of main.c has the following lines
The comment says "Use last page in flash". However, what I am guessing from the code itself...
I am trying to use nrf_serial with IRQ. Tx operations just fine but, i can not get any interrupt when a data comes from uart. I am using sdk 14.2 and not using ble.
