here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
Hi all,
We are using the BMD-340 from uBlox, which runs the nRF52840 SoC.
On this BLE Peripheral, we are running the ble peripheral demo project ble_app_uart (pca10056...
Hi,
I am trying to disconnect an Android smartphone from the nRF52840. After trying for some time we found out that the BLE stack of Android does not reliably closes a Bluetooth...
hi..folks
wish you happiee new year
i am using nrf52832 whille i tried to pair my device with my android , i am getting an error message " pairing rejected by nordic_uart...
Hi,
According to below thread, the advertising interval has a random 0 - 10 msec delta, so if the adv interval is 20 mses, if run it for long enough, will the result be...
Hi,
I would like to use the PDM interface for my application in nrf52840.
I configured the driver, and started using the SDK's API successfully.
Question 1:
During...
We want to achieve something like this -> We have several BLE peripherals with us and we are going to connect this peripherals to nrf9160 using nrf52 module and then send...
Hi,master
I want to learn DFU/bootloader, I am looking at the official source code, but my ability is too bad, I can't understand it at all. Is there any detailed information...
Hi
I read some threads about how to pair/read IKEA Trådfri.
I'm using nRF5840 dongle with the HEX code cli from SDK 17.0.0.
Using the terminal and send
bdb role...
I have both a NRF52840 (actually 2) and 2 dongles. I need to measure RSSI vs distance for a single link. I set up the RSSI viewer and it shows a blue or green bar for the...
I am getting unexpected behavior when using the latest version of the antfs.c sample code. I think this is a separate issue from what I reported here
When the ANT-FS download...
I've been experimenting with your online power calculator: https://devzone.nordicsemi.com/nordic/power/w/opp/2/online-power-profiler-for-ble for NRF52840. I see that the idle...
ble_nus_data_send is returning NRF_ERROR_RESOURCES. I would like to increase the Tx Queue size, but as it is not straight forward to increase by changing the macro BLE_GATTS_HVN_TX_QUEUE_SIZE_DEFAULT...
Hi,
we are using the nrf9160 for our fleet management products, and am currently working on downloading firmware updates from our server. I am using an HTTPS POST request...
