Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi I am New with nrf24l01+ and i made my first project it was working perfect with 2 nrf24l01+ without antenna . After the end of the project i change one of the nrf24l01...
I'm trying the given example < twi_sensor >. I connect nRF52 DK P0.26 to my sensor's SDA, nRF52 DK P0.27 connects to my sensor's SCL. My sensor runs at 400kHz, so I modified...
Hello, I'm new for mesh, have a question about the mesh dfu bootloader.
the source device of the mesh dfu shuld be connected to a host. how to assign the uart pin? is it...
I have to integrate a softdevice into an existing nrf52833 SES project. All the documentation I have found isstarting from any of the examples and using GNU Linker instead...
Hi,
I am trying to create an application for nrf52810 soc. I have a problem on selecting board name and the SDK version
I am having nrf52DK (nRF52832 soc) development...
Folks. I developed my own circuit using nRF 52833 and I`m trying to upload a new firmware via SWD interface. I'm not getting connected to the target for any reason. Is there...
Using SDK 17.0.2 and the nRF52840DK, I am setting up SPIM with a memory IC (not actually hooked up though, just looking at the signals on the oscilloscope). This code is executed...
I'm facing a problem with a product I'm developing. The problematic setup is as follows:
Two nRF52832 peripherals (S132 v6.0.0), each notifying on two characteristics...
Using: Windows Pro 10.0.19041 Build 19041
I'm trying to run Trace Collector for an issue with the nRF9160 and FOTA. I go to run the Trace Collector and it starts, but says...
I am using nRF52832. For reading ADC value for battery level percentage i have used 800k and 1M ressitor value. But while reading ADC Current cosumption is reached to 3 to...
I am trying to copy from this example:
https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode
but I get:
./nrf5_SDK_Current...
Hi,
I'm trying to understand the PSM availability of my local network.
After playing a bit with the RAT and RPTAU values, I found out that using RAT=16~30 secs and RPTAU...
