Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello all,
I use a nrf9160. In my program, I would like to use a watchdog to be sur than my application is running.
1. I would like to save some data in memory without...
I just downloaded nRF SDK 17.0.2 and installed Segger Embedded Studio V5.20a
I opened the blinky example for the nrf52840 (C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\peripheral...
Hi everyone!
I got a Nordic Thingy 91 and I have tested the sample Asset Tracker application. But now, I want to build and program my own application, I was reading this...
I have a problem with a call to sd_ble_gattc_read() made within on_primary_srv_discovery_rsp that is reading vendor service UUID and returns with NRF_ERROR_BUSY. I am following...
i am using mpu 9250 and and using https://github.com/Martinsbl/nrf5-mpu-examples this examples.
the question is can i use magnetometer on spi protocol?
because i have...
1. When I use NRF52832 as the ANCS client to get the notification attributes, if the data exceeds the size of a packet and requires multiple packet transfers, is it the BLE_GATTC_EVT_HVX...
Hello, I am working on a project which requires using FreeRTOS with the nrf9160. Setup: - Boards tested on:actinius icarus, Thingy91) - VS-Code with Ceedling as build tool...
Hi, I have implemented OTA DFU on Android with your official DFU library. We want the DFU to happen in background at a certain trigger (car driving, triggered from device...
Dear Members,
How can I connect via ANT+ to Garmin GSC10 ?
then display cadence and speed value in UART ?
Is it related with this function in ant_bsc_rx_d52_s212.uvprojx...
Hi
My problem is very simple but I don´t know how fix it.
I have a project in my work and it goes very well, but when I returned home,I have build It and it goes with...
Hello,
I'm having an issue with my nrf52832 with and ICM20948 IMU attached. My issue is related to wake up on motion. I believe I've set it right but I can't make it work...
Hi.
I have several issues when trying to respond to Direct Methods (using v1.4.0 of the SDK):
In azure_iot_hub.c:
evt.data.method.rid = atoi(topic->prop_bag[0].value...
Hi !
I am working with a NRF52832 and with SDK 15.2.
For my application, I need sometimes to deactivate the Softdevice to begin some radio tests.
So I have programmed...
I am doing the procedure described in the nRF52840 specification, figure 193 "UARTE reception with forced stop via STOPRX".
I am using 1Mbps with hardware flow control....
