Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hello, regarding to another thread in this forum the debug interface mode can be turned off by sending the command "writeDP 1 0" via J-Link commander or by power cycling the...
Hello,
I'm working with the nRF5 SDK for Mesh v4.2.0.
During the init phase, I call the function mesh_stack_init()
After doing so, the consumption is on average 2.8...
Hello DevZone,
SDK 15.0.0 SD S140
Currently working without an active SoftDevice but even with an active SoftDevice these problems keep occurring.
I'm currently working...
Hello! I need help implementing a TDMA on a nrf52. I've never done this before and Its been hard to find good resources online on the topic so if anyone here has any previous...
I am developing connection between BM833AF Evaluation board and nRF52840, Like a BLE Tag and Beacon. Need support in connection and transmitting data from one to another?...
Hi,
My use case is I have an RGB LED that I want to be green for normal operation, but blink red for 0.5s when a serial driver error occurs.
R, G, and B are each attached...
Hello,
I have multiple questions regarding BL mesh using nRF5 SDK for Mesh v4.2.0
1) is it possible to run this example using 2x NRF52840 dongles(PCA10059) and one NRF52840...
Hello
We have an application that ADV every second and is based on SDK 14.
We are currently attempting to move to SDK 17. What I have noticed is that if I change and...
HI,
I want to use nrf52833 for receiving SAADC DATA in my phone by using BLE_NUS_DATA_SEND.
Here are my codes.
In 716 ~ 724 lines, I added codes about BLE_NUS_DATA_SEND...
Hello
I'm using the nrf52840 DK with sdk version of 15.0.0.
My requirement is to flash my project through cli commands, so I have followed the following steps in below...
Hi,
I recently updated my toolchain using the nRFConnect tool chain manager.
(I was seeing problems after an OS update)
This update fixed my problem but when I build...
Hi,
Please, what are the settings for gpio driver in sdk15.2. for some gpio pin to be able to sink current (to act as gnd? ). In my project it is used for loadswitch enable...
Hi,
I have bumped into this bug in SDK v17.0.0 and SDK v17.0.2 but no fix yet.
We are using nRF52840 with S140.
Can you please make sure to release this fix asap because...
Hi There - My question is about the nrf5340 dual core cpu. I’d like to know if it is possible to have one core polling sensors on the spi bus - then pass this data to the...
Hello
I am testing sending the value to the app through the ble_app_uart of SDK v17.
I know roughly that I need to use 'ble_nus_data_send', but it is not printed from...
