hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello,
I'm having issues getting my SPI to work at high transfer speeds. I have my pins configured to have high drive.
SPI is set to MSB first, Mode 0.
Colors:
Brown...
Hi All,
I am using SDK17 for my application currently. To sense ping change I am using app_button function as below. Normally my port pin remains high and current consumption...
Hi,
I am working with a NRF52840 with the SDK16 and I am facing field issues with the peer manager flash usage. At each connection the app subscribes to characteristic and...
Hi,
I wonder there is not any TX_POWER_LEVEL macro used/defined in the source code of below peripheral application.
"examples\ble_peripheral\ble_app_hrs"
Does it...
Hello, sorry to bother once more.
I am new to the nRF world and bluetooth in general, I am trying to build a device /app that gets data from 3 sensors. 2 of which operate...
Hi all,
in order to put the whole project under a decent version control system I need a list of all files used in the example project in segger studio.
The c source files...
Hello! I have the following issue with my nRF52833 board: I am in the first stage of working with it and I wanted to try the simple blinky example.
However, since there...
Hello,
I'm beginner with Nordic nRF52 devices.
I'm working on a PCA10040 (2.1.0) dev kit and I would like to communicate through TWI interface.
Then I have installed...
Hi! I was defining NRFX_WDT_ENABLED in sdk_config.h, but found that apply_old_config.h was undefining it.
Even though I had WDT_ENABLED defined to zero, the test in apply_old_config...
Please, give me an advice. I need to measure the supply voltage and trigger an interrupt after the measurement. An END interrupt is triggered only once. It must be without...
What's the difference nrf_cloud_agps and AGPS using google SUPL data?
I'm not clear about this. README.rst doesn't explain about it.
Also, to use the nrf_cloud_agps, do...
Hi Devs,
I am facing a weird behavior with my application, where the TWI writes return NRF_ERROR_DRV_TWI_ERR_DNACK or NRF BUSY
If I ran the TWI writes from the main...
Hi Nordic,
Does SLM application support IPV6, if yes could you please point us to the AT command set which configures IPV6 and also point to us complete AT commands list...
