Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I am working on a device that has nrf52 as an additional BLE chip that does not run the main logic but provides UART over BLE to the application processor (NUS). In...
Hi,
I am working on the our customized board nRF52832 , interfaced with MAX30205 temperature sensor . I am advertising the data only when it reaches the below temperature...
Hello,
We are planning to use the accelerometer in the Thingy91, we have some inconsistent results when configuring/reconfiguring, we have 2 questions:
- When we, for...
Hey,
We've been having issues with a subset of a batch of devices produced recently, with an unacceptably high failure rate when switching to DFU from firmware (the switch...
Hi everyone,
Is there a function like APP_USBD_CDC_ACM_GLOBAL_DEF or APP_USBD_MSC_GLOBAL_DEF that allow to define a custom class?
I want to define a custom class using...
Hello there,
I am using the nRF52832 and I need to talk to 2 different UART based peripherals.
In order to do that I was thinking to use the libuarte module in time...
Hi
There are already several questions regarding UART clock source, e.g. that one for nrf52 where it is stated that the peripherial always take the 16 MHz clock.
Is this...
Hi, the nRF21540 FEM is out for quite a long time. However, there is still no direct support in NCS. Fortunately. some work has already been done. This PR introduces the FEM...
I want to add some logging to my nrf5340 net application and I'm having some troubles.
I have the following in my main.c: #include <logging/log.h> LOG_MODULE_REGISTER...
Its clear there is little interest in this DK compared to the nRF52 version. I got instructions for that platform that actually worked.
Not so for the nRF51 DK. But I am...
I am using FreeRTOS and some of the commands there have two flavors: for using in regular code flow and when are executed from an ISR, but in nRF SDK components and examples...
Hi All,
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer.
My setup: HW: PCA10040 SDK: 17.0.2 Project: nRF5_SDK_17.0.2_d674dde...
Hi,
I followed all the steps to get NCS up and running with SEGGER Embedded Studio. However, when I try to open an example, I get this error:
Including boilerplate ...
Hi all,
I am currently working with nRF52832 boards, and I am trying to save some values in my flash memory. I have already created a code for this purpose and I am able...
