Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I have made a custom board using NRF52832 (NRF52832-QFAA-R/QFN-4) with 32MHz and 32.768 kHz crystal. The SDK is nRF5_SDK_17.0.2_d674dde. It can be connected using nRF52840...
During the initialisation adding gatt attributes with the function "sd_ble_gatts_characteristic_add" i get the error NRF_ERROR_NO_MEM. So it seems the default table size is...
We have Thread devices with bootloader and applicaion based on nRF5 SDK for Thread and Zigbee 2.0, and now we are migrating to SDK 4.1. As it's stated in documentation the...
Hi! I'm developing an augmented wearable project using Bluetooth (eg., Smartwatch). I'm planning to use the nRF52810 chip for it. We are just going to add a couple of sensors...
Hi
win10 64-bit system。Reinstall the system and rebuild the development environment。Reinstall the system and rebuild the development environment. Can't solve the problem...
I can see in Segger Embedded Studio v4.52 under the Build Tab, there are two methods to build the project.
1- Build > Build zephyr/zephyr.elf
2- Build > Build solution...
sdk16.0 ble_peripheral/ble_app_hrs example
I start on nrf52840 DK with the SES
I run the following commands
nrfjprog --recover
nrfjprog --eraseall (?? just because...
I want to add peer to my project_ manager_ Init() implements pairing binding and whitelist. My project is S112 under pc10040e directory The reference routine is e: workspace_...
I want to test the mesh,but Idon't know hao to fine the path to nRF5SDK instance
..\nrf5_SDK_for_Mesh_v4.2.0_src\examples\sensor\server\sensor_server_nrf52832_xxAA_s132_7_0_1...
We are developing a device that has different "modes", and in some modes it acts as a HID keyboard and mouse, but in other modes it does not. This device connects to iOS and...
Hi guys,
I am using the nRF52832 board and after I enabled my device to measure the temperature and return this value, now I will like to save that value in non-volatile...
Hi,
Had a project working and compiling beautifully, all ready to go, last thing to do just upgrade the SDK from 17.0.0 to 17.0.2 and the s132 7.2.0
So I change the...
Hi
I start in programming on nrf9160 DK with a sensor BME280. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hello, dear sir:
In my opinion, HFXO means external oscillator, I need to buy a external oscillator because it is not exist in nRF9160?
HFINT means internal oscillator...
