Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi everyone,
I am using the custom nRF52840 module provided by Raytac. I integrated into my evaluation board and I flash it using SWD and JLink debugger. My problem is that...
I have DFU code base working. It consists of a thin layer of our code, and majority is from Bootloader component from SDK v17.
I started with DFU OTA, and then incorporated...
Hello,
I am trying to reproduce the Mesh Light Switch demo at home now, with my own dev equipment and have hit some problems I did not expect -
Problem:
nRF52840 Dongle...
I have developed an app for the nrf51822, using the nrf51-dk with SDK12.3, together with DFU functionality.
After having solved many issues to get to this point with the...
Hello, I'm using nrf52832 with SDK 15.0 and softdeveice 6.0.0.
I need to handle interrupts with different priorities on two different I/O pins. How is the correct configuration...
Hello, I'quiet new in Zephyr.
So tell me if I'm wrong.
I would like to test driver mcp23s17 present on zephyr.
I've add in .overlay file
And now I want to initialize...
Hi all,
I'm programming nRF52833 with SDK17.
I want to use only one channel (for example 37) to broadcast advertising during advertise interval and also one channel of...
My team was looking to transfer a 20-byte value (or 'message') between a mesh client and server, what is the best way to achieve this? I have practiced with the light_switch...
Hi,
I am currently developing an application for the NRF52840 using a custom pcb powered through the VDDH pin using a 4.2v lithium ion battery. Part of my application requires...
Hi,
I am trying to following the instructions at: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_user_guides_java_coaps...
I have configured the dev kit by cutting the SB9 bridge. I am powering the device from the J2 USB port on the DK. I have not bridged SB12 or SB11 as I am powering the device...
Hello all,
I am experiencing a ~5uA oscillation (between 5uA and 10uA) in sleep mode, DC/DC converter enabled, no RAM retention. The total current is of the entire system...
i am working with jlink segger edu, in a custom board, it dont have swd TX, RX pins connected, only jtag pins. I Need to see if my gps conected throw uart is working or not...
I configured the pca63519-sr3_nrf52832_shield to fit on my board (actually disabled all peripherals, only the bluetooth protocol part), but found that the modified code could...
