Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I am using the nrf connect desktop application on windows with a PCA10059, and have found the application to be buggy when receiving a flood of notifications, this works fine...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
Hi,
I was using nRF Mesh application to get the data of uint32_t from my server model(nRF52840) but nRF Mesh android application crashes while sending the opcode to the...
I am searching for complete developement kit and SDK support which can be used to form BLE mesh Network and BLE beacon device. The idea is that BLE mesh nodes will act as...
Good afternoon, dear Sir of Madam.
Our product used the NRF21540-QDAA-R7 which has gone obsolete. What is the best substitute part?
Unfortunatelly i couldn't find substitution...
Hi I am facing a issue regarding the DFU update using the nrfConnect App.
Since we recently updated from SDK12.0 to SDK16.0 and the softdevice version has been changed in...
Hi,
I am analyzing the power consumption of mesh nodes using your Power Profile Kit. I am running the example beaconing of the Mesh SDK 3.1.0 on a board nRF52832 with the...
I have designed a nrf9160 debugging board, which uses 18 and 19 pin as the log output. Then I also configure the TX and Rx of UART0 in the overlay file, which are 18 and 19...
i tried with blinky example like thiis
#pragma long_calls
__attribute__((used, long_calls, section(".data"))) int main(void) { /* Configure board. */ bsp_board_init...
Hi,
I'm working on a code using SPI.
I've changed the SPI configuration from this thread: https://devzone.nordicsemi.com/f/nordic-q-a/65072/nrf5430-spi-sample-code ...
Hi,
I'm working in a project where we try to implement an Isochronous broadcaster using timeslots, co-existing with Softdevice controlled Scanning and Connecting. We use...
