hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi, I got an SDK15.2 project that we converted the bootloader to be both serial and ble for the dfu. Unfortunately we have a few units in the field that have only the BLE...
Hi,
I want to schedule timeslots back-to-back, or as close as possible. Question is how close to eachother timeslots can be scheduled?
I read the following about sd_radio_request...
I have a custom BLE service that works correctly with nRF Connect. When I use the API, though, it sends me the same value repeatedly and does not update to reflect new values...
Hi,
I am a developer of IoT systems working for a private firm within Africa. I currently started the development of a cellular IoT solution and my search landed me on the...
Hi,
I've somehow managed to build the gps sample from source within SES, but I can't get the flashed sample to work properly. Everything is fine if I flash the downloaded...
https://devzone.nordicsemi.com/f/nordic-q-a/46388/nrf9160-dk---make-application-from-scratch
I followed the steps from user: Aakash_Soni on this thread. However, when...
Hello,
I am using Segger Embedded Studio IDE v4.52 (64-bit) to develop an application using nRF5340pdk.
My question is this, I cannot find any of the Preprocessor or compiler...
Hi.
I am developing using nRF52820 with SDK 17.0.0 . I test the USBD using the example code(\nRF5_SDK_17.0.0_9d13099\examples\peripheral\usbd_hid_generic), but the problem...
Hi,
I would like to know if it's possible to read advertising data when connecting to the peripheral.
My problem is sometimes when i read the adv data, and then try to...
Hi,
I try configure 2 gpio pins with opposite pull state, one NRF_GPIO_PIN_PULLUP, other NRF_GPIO_PIN_PULLDOWN :
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_LOTOHI...
Hello
We are working on BLE remote based on nRF52810. We are operating it through coil cell. Please let us know is there Internal battery monitoring feature supported by...
Hi--
I am running a application that executes in the bootloader region of memory (0x70000 to end of memory), and is using FStorage to overwrite the application memory space...
Hello, I am on a NRF9160-DK and I am using SDK 1.3.0 I am working on the AWS_FOTA project. I'm trying to configure the sending of a message in MQTT when pressing a button...
Its a first time, we are using the Nordic product. Please let me know how the step-by-step software installation procedure and would like to know the software cost as well...
