Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello,
It looks like several people are having issues updating the firmware of the Thingy:91 modem with a simple USB cable.
I personally tried on Windows 10, 8 and 7....
Hello There,
I have problems with the installation of the nRF9160. Started the installation earlier and nRF9160 was detected in nRF Connect/Programmer and I could see memory...
Hi, For my application I was using ESB without softdevice and just recently I wanted to add dfu so I had to add softdevice as well. After adding softdevice I found out that...
I want to convert APP_TIMER_TICKS ms to us.
So i'm using this function.
And, the value of APP_TIMER_CONFIG_RTC_FREQUENCY is
Also this is main code.
And, I...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
Is there a modified radio test firmware available? I am hoping for something that can be connected to via BLE, command it to turn on a tone, and then reboot the processor...
Hello,
I'm trying to send and receive data between the nRF52832 chip and a phone by following this tutorial:
https://github.com/bjornspockeli/custom_ble_service_example...
Hello!!
We are carrying out a project using nRF52832 , in which we must send a data to a phone every 1 second for 10 hours. The data sent is a sequence of numbers from 1...
I'm using Eclipse CDT for debugging according to the tutorial on this site. I've installed the device pack and I do see the nRF52 peripherals in the debug view. However all...
Hello Out There,
The Getting Started, it states as follows.
The following steps are required for nRF9160 DK versions UP TO v0.9.0. Newer versions of the nRF9160 DK contain...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
Hi Friend,
I use nrf252832 MCU and SDK 15.3,
I would like to Implement below function,
1:Device bond phone A without password first , the phone A popups a bonding dialog...
Hello. I've migrated my application from SDK 14.2 to 15.1 and I obtain this strange message from peer_manager_handler in my log: I obtain this message only when I connect...
Im trying to enable the Scheduler on a mesh example, but Im getting "1127959>, app_error_weak.c, 108, Mesh assert at 0x0002C9E4 (:0)" each time I try to add or connect it...
Hi,
I want to close uart by using app_uart_close() for low power, but can not init uart again by using app_uart_init() or nrf_drv_uart_init().
More I had try TASKS_STOPRX...
