Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I am trying to follow the tutorial SDK UART coexistence example , but it seems like the last step cannot be completed. As you can see, that .hex file does not exist...
I am working on a low power peripheral project (similar to the Nordic blePeripheral/uart example). I'm going to be using an nRF52805 with SDK 17 and s112. I found the Apple...
Dear all,
I have tried my best to find answers in questions posted previously but I still have a few questions that I would like to clear up. I will keep it concise. Thank...
I want to configure the UART1 (not the UART0), and I want to know if there have some examples that introducing the UART configuration by directing accessing the register....
Does Nordic have programming for the nRF52840 that enables both 802.15.4 and BLE, so the board can both become part of an 802.15.4 network and pair with a mobile device like...
Hi All,
i played with the /examples/dfu/secure_bootloader/pca10056_S140_ble_debug.
The application works fine so far.
I do have the following questions.
Is it...
Hi,
I am running into some problems with libuarte. I have two nRF52840-DKs talking to each other over UART. My setup is not ordinary however. The hardware configuration...
Hello -
We are developing a product for the nRF52840 using SDK v17.0.2 and FreeRTOS. Our application uses the RTC configured by FreeRTOS to implement a System ON sleep...
While installing the itsybitsy NRF52840 board from Adafruit in the Arduino IDE, I encountered the following error:
"Tool nrfjprog is not available for your operating system...
I can't get a button to work on a custom board; but same firmware HEX file on a different board works fine.
Using nRF5 SDK 17.0.2, SoftDevice S132 v7.2.0.
using a custom_board...
Hi,
I'm using an nRF52840 and I need to implement a driver in c for an external chip. The c driver is written, and I only need to add specific functions regarding the SPI...
I can't see the answer, so I will write it again.
hello.
nrf24l01p(ptx), nrf51822(prx)
nrf24l01p set
TX_ADDR = 0xA5B300
EN_AA = 0
EN_RXADDR = 1
SETUP_AW =...
Hi, I am trying to add Buttonless DFU functionality to the ble_app_blinky example.
The process I took
1. added the following files to the project
ble_dfu.c ble_dfu_bonded...
Hello, I am trying to implement a basic BLE connection between the nRF52840 Dongle and an Android Device (nRF Connect). I wanted to secure this BLE connection with a passphrase...
