to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hello,
I'm using the nrf52840 and SDKv16 to interface with an SD card. An SD card block is 512 bytes. I would like to do this:
1. Get the card ready for a write (use blocking...
Hello,
Not a 100%, but in this Nordic video the nRF52840 might be using the Alexa Gadgets Toolkit. Alexa Notepad demo 2020 https://www.youtube.com/watch?v=CdLfg-6kQs0
...
Received our 52840 DK, loaded, via nRF Go Studio, s140_nrf52_7.0.1_softdevice.hex. Loaded, via IAR Workbench, ble_app_blinky_pca10056a_s140. I clicked to go button and whamo...
Hello. Nordic team.
Once again I had questions, this time related to serialization .
While the preparation of the driver is on the PC side, I am studying the examples...
I have an issue with reseting the board using a hard reset via an external button. The onboard development kit reset works, but I am trying to perform the same task using...
Hello,
I was reading the nrf_libuarte_async library, and noticed that in the
app_timer_handler -
calls the
local_app_timer_start -
again and starts the timer again...
Hi,
I use a 3rd party board from raytac ( https://www.raytac.com/product/ins.php?index_id=95 ) on my PCB and I have problems with a bluetooth low energy connection. On your...
Hello,
I'm trying to get sleep mode working on a nRF52840-DK with Zephyr or Mbed OS while using UART.
It is possible to achieve low current consumption in sleep mode...
I opened an example from the SDK 16 in:
nRF5_SDK_16.0.0_98a08e2/examples/iot/lwm2m/lwm2m_client/pca10056/s140/ses/iot_lwm2m_client_pca10056_s140.emProject
When I try to...
Hello!
I want to develop my own app, and the source code refer to proximity in nrf toolbox. Now, i have some questions:
1. What function in the source code of serverManager...
Hello
In my application, I would like to allow smartphone that are Bluetooth V5 compatible to receive more information in advertinsing packets from my devices (via the ...
Hi,
I want to optimize the transmission efficiency and thinking of sending larger packets than 2048 bytes of MQTT would help.
We have limited battery power, and looking...
Hi,
I am started working on nRF9160 Power Management. I want to power down all devices(sleep mode) expect motion sensor, Wake if motion is detected. I went through System...
Hi Team,
Can you please point me where I can change the compiler optimization level in SES v4.52 and I am using nRF9160 module.
Regards,
Praveen Palaparthi
Hi Team,
We are using the NRF52840 Device with S140 Soft device for our BLE applications. As part of this we have enabled the flash storage as well.
We are unable to write...
