I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi
I would like to know the availability of the open sources for the following:
1. BLE Gateway for PC, Android , iOS
2. nRF Cloud open source
Can you help, How to...
The nRF52840 UART example uses pins 1.13 and 1.14 for the TX and RX pins on the Dev Kit (uart_pca10056) and has a default baud rate of 115200, but the 1.13 and 1.14 pins are...
Hi! I'm having issues with inconsistent battery readout results. I'll elaborate more below, but in general, I have multiple devices which 'sleep' most of the time, and when...
I have an issue when i am doing writing of a structure where autoprog is a struct like this :
typedef struct { uint8_t tag_tab[TAG_ID_LENGTH]; }tag;
typedef struct { uint8_t...
Installed nRFgo Studio lastest win64 verion nrfgostudiowin641212installer.msi and lastest windows 64 nRF-Command-Line-Tools_10_9_0_Installer_64.exe . But nRFgo does not work...
Hi!
I want to develop a simple program which count pulses in a digital pin in an interval of 10ms. I want to use a timer as a counter to count the pulses, also I want...
Hello Nordic Team,
We just received and test a new batch of SIMs using a nordic nRF9160. However, there is an error that doesn't allow to register these new SIMs. From LTE...
Hello,
we have a project on:
Periperal: experimental ble_app_blinky / and
Central: experimental ble_app_blinky c
We have add suplementary:
LEDBUTTON_LED4 ( BSP_BOARD_LED_3...
Hi,
I am unable to test current time service example.I followed all the steps mentioned to test CTS Example.But, below are the log messages:
Again if I try to reset...
I have an issue with my nrf9160 custom board.
I flashed successfully only 3 of 30 pieces batch. Other boards fail with "Failed to connect to target. No idcode detected"...
Hi !
I am working on aws_fota, with a nrf9160 dk, sdk 1.3.0. When I try to connect in mqtt, I get my IPv4 address I get the following message: ERROR - mqtt_connect...
Hello,
I'm trying to interface msp430fr5994 to nrf51822 as spi slave with soft device 110 and SDK v10. The master (msp40) sends 20 bytes to the slave (nrf51). The issue...
Hi,
I started debugging a device with an nRF52820 chip and found that the pinout is similar to nRF52833.
The test application was switching pin P0.15, but the ripple...
