But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I am using nrf52832 (S132) with SDK17. I want to store some data in the flash memory dynamically. So what would be the maximum and minimum flash memory that I can utilize...
I would like reduce TX Power in DFU secure bootloader, I would like use sd_ble_gap_tx_power_set function but I faced with the following problem, I don't know how to get conn_handle...
Hi
I am working on the GPS for Thingy91. The Thingy91 is able to get the fix when I am outside and test it. However, when I am in the building by the window or on the balcony...
Hello ,
I am bit confused about the minimum and maximum connection interval . what does mean ? it is time interval for the connection or else time interval for the data...
Thanks in advanced. Platform is nrf52832, SDK_17.0.2, use nrf connect app. I create custom service. If I set 128bit base uuid: {0x9E, 0xCA, 0xDC, 0x24, 0x0E, 0xE5, 0xA9, 0xE0...
Hi, I'm testing ble mesh using the "Mesh Light" sample with my developer board using Zephyr.
My components are: - My device: Makerdiary.com nRF52840-MDK development board...
Hello world :-)
I would like to use Bluetooth Low Energy Sniffer [1] and 802.15.4 Sniffer [2] on nRF52840 DONGLE using my FreeBSD workstation. I did manage to build the...
Hi!
I am trying to utilise the BLE SIG service for environmental sensing (0x181A) with the characteristics for temperature (0x2A6E) and humidity (0x2A6F). I would like to...
Hi
I'm trying to build blinky example (from SDK17.0.2) to run it on nRF52833DK.
The board is running correctly if I download the hex comes with SDK but failed if download...
Hi, I'm writing a library for the common Hitachi_HD44780 (LCD2004 etc) but need it to be non-blocking. I'll open source it once done. I'm using EasyDMA to do the transfers...
Hello,
I am trying to solve my issue for few days without success hence your help would be appreciated. I found a lot of related issues, but any of the solutions doesn't...
Hello,
I am using nRF52840 chipset and I was using the Segger tool chain properly. But recently I started getting below error "The evaluation period of this release has...
Hi,
I am doing the project in nRF2832 , where I need to collect some data from the sensor and temperature value that i need to save in the .CSV file format in SD cARD ....
Hi,
I have a question about setting the gpio pin status. From the picture, it seems that the value on the right represents the status of the gpio pin. So the default value...
