Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I've developed a little test application on a nrf52832 chip to run fstorage in a bootloader memory address. I followed the nordic guidance to set up, build, and install a...
Hello, The card has already been assigned to an NRF Cloud account. However, we wanted to change the account card for a practical reason. We have therefore deleted the card...
I tried using nrf52832(as slave) communicate with stm32, it successed .
But when I changed nrf52832 to nrf52840 to do the same thing, it failed .
I use the nRF5_SDK_15...
Hello there, I following the nRF IoT SDK getting started and after Connecting Devices to Router section I succeed in connecting devices to router.
After that, I edited...
Dear Nordic Team,
I was trying to understand event handlers from SDK5 examples. I understood that by using following macro we can register our event handlers, and afterwards...
Hi, I'm trying to run the JLink debugger using Ozone to debug my program. When I run nrf_crypto_init(), I encounter a hard-fault. The program is not experiencing any problem...
Hi,
I am trying to develop an application on nRF52840 development kit board. When I am trying to build I am getting below error "nrfx.h: No such file or directory". For...
I am trying to port BLE_APP_Interactive to nRF52840 as I require 2 uarts in my application and larger memory. I realise I need to change the crypto to CC310, and I have followed...
I've been seeing issues with getting an interrupt on the TX side. I reckon it could also be linked to the RX module cause if the payload isn't sent, the interrupt on the TX...
Hi,
I have implemented a custom bootloader/firmware package, but have recently been running into issues when integrating the two. I have found in some instances when using...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
When trying to build/run the btle throughput demo I get a device not supported error.
When looking in the Options - Device settings for
the project the Software Packs...
Hi All,
the logging output (NRF_LOG_...) in the SDK17 via the UART works fine on the DK board (only change from the HRS example was the NRF_LOG_BACKEND_UART_TX_PIN has been...
I am using nrf mesh SDK 4.0 with nrf52832 DK and nrf mesh android app , with the light switch exemple , i noticed that a proxy node that was successfully provisioned can be...
