Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hello,
I am trying to send something by my own via UARTE0. This is only for testing/learning purposes:
This is what I see:
[00:00:00.000,000] <info> app: enable...
Hi,
Can I control warm light as well as cool light using the CTL+LC server example provided in the Mesh SDK v4.2? Or does it support only warm light?
Moreover do we...
This is my log
Loading solution asset_tracker.emProject Executing load commands cmake -GNinja -DBOARD=nrf9160_pca10090ns -DBOARD_DIR=C:/Workspace/nRF9160/ncs/zephyr/boards...
Hi,
Currently I am setting up my work environment. I have a simple Zephyr project running on our custom board with the nRF52840, so a modified example and a custom board...
Hi Folks,
I am currently working on a BLE configuration composed of two NRF52840 chips. One is configured as central and the other as peripheral and use coded phy (long...
While I am going to pair with my android 9 Asus mobile phone with SDK 17 nRF52840. It in my mobile showing "Pairing rejected by Nordic_HRM". After that I have added a some...
Dear community,
I am trying to implement a custom service, however I am struggling because many example codes are for PCA10040, Softdevice S132 and/or for older SDK's. I...
Would it be possible to get the SHA256 hash for version 5.1.0 of the S132 soft device for the nRF52832? Just want to verify the integrity of the download. Thanks.
Hi All,
I am currently designing my PCB using nRF52840 chip.
I was using the footprint downloaded which was in nRF52840 dongle pcb library given by Nordic. During DRC...
Hello,
I am using Nrf51822.
I am using sd_110/application/bootloader, etc. in SDK_10.0 without problem.
Recently, migration to SDK_12.3 / sd_130 is in progress to...
How wide are the peaks? I know that it depends on many factors how high and long the peaks are. Currently we have measured peaks of 450 mA for 40-50 ms in our application...
Hi,
I am trying to run the Zephyr BME280 sensor sample application (using nRF9160 DK) in NCS1.3.1, but get the below error:
My prj.conf is as follows:
And board...
Hi all:
I install "nRF Connect SDK v1.3.0" by Toolchain manager,
but it always show "Failed to clone the repositories".
Could you have any suggestion?
best...
I am trying to interface my nrf51 DK with the Lis3dh sensor . I have one reference code by elmot for the project and it is working.
https://github.com/elmot/nRF51822xxAA...
Hi,
I'm comparing the nRF9160 DK and Thingy 91. The purpose is to copy the LTE RF design for a Band-20 application. The GPS will not be used.
Question: Is the complexity...
