I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi
I am using NCS desktop application
I ported it to my custom board(52833)，It works well
but now，my custom board has three leds，while nrf52 kbd board only has 1 led...
I need to build a simple BLE dc motor control with a potentiometer to provide the rotational position of the motor.
Anyways, my first step is understanding the Nordic libraries...
I am new at Bluetooth. I want to design remote media control(volume up,volume down, play/pause, next track,previous track) and call answer or reject. I have tried to make...
Hello there,
I am encountering an issue with the zigbee light_control example on the SDK v3.1.
Before I explain the the problem, here's some detail about the system setup...
Hello,
I am attempting to retrieve a device's own MAC address and print it out. So far I have encountered two different functions that can help me achieve this.
void zb_osif_get_ieee_eui64...
Hello
I'm working on the example of app_uart in sdk v17.
I'm trying to create a button 'Long Press' feature, but somehow the button input isn't working properly.
Below...
The example app_onoff.c shipped with SDK For Mesh 4.2.0 (unchanged from 4.1.0) have two unused variables in its state struct.
The value_updated variable looks like a left...
Hi
Is the GPIO on the nRF62840 5V tolerant?
I see the VDD supply is capable of 5.5V.
I’m running a 5V Hall effect square wave into the GPIO pin used as an interrupt...
Hi Team,
I would like to send 10 bytes of data in mesh from one device to another device. As i know that we can send data from one device to another device and the packet...
Hello,
I've asked this question around 6 months ago. Now I have to pick up where I left off and I was wondering how much the situation might have changed since.
- Last...
Hi there!
Okay, I've been trying a lot to figure this out, but without any success. I have absolutely no idea what could be the problem whatsoever. The problem is that the...
Hi,
Currently we working on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V4.52
SDK v1.3
CONFIG_MQTT_LIB_TLS ...
I am currently unable to flash any new code or to erase the flash memory of my nRF52840 Preview DK boards.
I am using SES and the OB J-Link, but also tried JLinkExe and...
Hi, I am using the TIFS register of the NRF RADIO to define the interframe spacing timing. (Done with the following line)
During a 1Mbit or 2Mbit connection, the real TIFS...
