I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello everyone,
We're looking to develop a prototype of a very simple panic button. The device should automatically pair with iOS / Android, and establish a call to a given...
I have an example application executing on the nRF52840-DK on SDK15.0.0, see https://devzone.nordicsemi.com/f/nordic-q-a/67351/are-there-any-differences-between-sdk15-and...
When we try and stream BLE data to the nRF Connect app on an Android or IOS phone the app accepts our requested for an MTU of 244 or 160 respectively, however it does not...
Hi,
Dev setup:
Segger embedded studio - fatfs example - SD card - nrf52832
I am able to write to sd card and see data. But while reading i am failing.
Below is code...
Hi,
I am a bit confused after looking through all the SDK solutions available for NRF52 and need a piece of advice...
I am have started on the project that consists...
Can I periodically or continuously read the characteristic of peripheral after the connection?
If there is a change in the value in peripheral, then the value is received...
Hi,
i am trying to do buttonless dfu . I want to merge all hex files into one as per the document .when i enter the mergehex , i am getting mergehex command not found why...
Hi,
I'm making an new board with both nrF52840 and nRF9160. In addition to the radio ICs there will be some antenna diversity switches, chip antennas etc.
So I'd like...
Hi,
I'm using SDK 15.2 with Nrf52832,
I've implemented a custom service with read, write and notification services.
I would appreciate if you could send me an example...
Hi,
I have a problem with the NRF52840 DK rev. 2.0.1 coin cell. When powered via USB board is working properly but when powered with coin cell nothing happens.
SW08 is...
I bought a development board nRF52840. Connecting it to the PC (WIN 10 x64) will not recognize the device. At first I thought it could be the cable, bought a couple and it...
Hi Team,
One of our requirement is to measure the crypto functionalities timing like how much time it is taking for digital signature signing and verification. Is there...
I wanted to know if there any any static analyzers that work well with the nRF5 SDK.
I was thinking about adding a static analysis (e.g pc-lint) check to our code base and...
1. When I loaded the 9160 project, I had problems,
arm-none-eabi-gcc.exe:error:CreateProcess
9160 development environment, the required software, I have installed...
1. When I loaded the 9160 project, I had problems,
arm-none-eabi-gcc.exe:error:CreateProcess
9160 development environment, the required software, I have installed...
