Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I have a nRF51 DK. I am trying to sniff the Bluetooth connection between the smartphone and watch at Window 7.
Installed:
Wireshark 1.10.7
Sniffer (tried ble-sniffer_nRF51822_1...
The sdk_config.h configuration file for ble_app_hrs_freertos example contains following definition:
#define NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS 1
This macro should...
HI,
I have connected to one peripheral from my central and retrieved all the services(For example i need Device Information Service, got all the characteristic values) and...
dear sir,
i have a nRF52DK board,
i want to power on the board but not glowing LED and my laptop not detect the board while connect with laptop,
please given solution...
Hi
Env: keil and no SD
I am doing the first steps on keil + nordic nrf51822. I started by opening the Blinky app (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples...
Hi there ,
i am developing a biomedical recorder which needs to continuously transmit the recorded data ,
data rate is very low (9.6 Kbit/s to 32Kbit/s) but i have a very...
Hello,
I was wondering whether or not there is a way to know, how the connection interval is decided between the two values of the Connection Interval Max and Connection...
Hi, everyone,
We develop the project by using nRF52822 module. But suddnely we discovered that the latest supporting this chip sdk versionis 12.3. The SDK versions newer...
According the the instructions for the Thingy mesh demo, it is possible to manually provision new nodes. Is it possible to identify the unprovisioned node first by sending...
I am trying to make the nrf52832 enter in ON/low power mode for inactivity periode.
I must have the "System ON, No RAM retention, Wake on RTC" as indicated in nrf52832 datasheet...
Hi,
I run the Secure DFU, and I'm doing OTA update without any issue.
The problem is the case that I'm doing an OTA update with a application-version smaller than...
Hi all, Nordic distributors no longer carry the nRF52840-PDK, which included the NFC antenna. What is a direct replacement for the Nordic NFC antenna that used to be included...
I am trying to connect a BerryMed MD1000 Pulse Oximeter (BLE Server) with an Adafruit Bluefruit Feather (nRF52-enabled) Arduino board (BLE Client).
I made an Arduino sketch...
hi All!
I use WAKE UP event from G-SENSOR on some GPIO to wake up the MCU on motion detected.
But sometimes ( ~1% ) the event does not occur for unknown reason until RESET...
