I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Can someone explain the indepth working of nrf dfu bootloader example with respect to the init packet.
How is it decoded and the information gets stored in the structure...
Hello,
I'm getting started using the nRF Sniffer with PCA10040 and Wireshark on MacOS. I followed the instructions in the User Guide and was finally able to set it up by...
Hi
This is just a head's up. In function nrf_esb_pop_tx(void) you have the following code ...
Instead it should be the following...
Otherwise the bug is such that...
The Introduction page is inconsistent:
infocenter.nordicsemi.com/index.jsp
first it says
[quote]]The mesh stack is also compatible with the nRF52810 platform, but not...
Hi all,
As I've been researching, the mesh sdk is not supported on the nRF52810 SoC, although being compatible. Is there any development or plan in changing this? I'm planning...
Hi,
Is there any way to add conditional compilation in linker file?
I have two versions of a code, one with DFU and one without, i want to combine the versions. is there...
Hi everyone,
I used SPI interface to access a external flash with page size 256 bytes.
I found I can't access full page, because the maximum of one SPI transaction is...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send so how to set spi latch reset turn on parameter...
Hi, there
I try to use the nrf_atfifo in my program, but I found the atfifo cause hard fault in my program,below is how I use the at_fifo in my program.
and I also found...
Hello, I have a problem with my nrf52832 customised board
It has loaded the ble_app_uart example of the 15.2_SDK and It have the correct pinout from my board, These are...
1. I try DFU bootloader with OTA, it success.
2. But the Application was gone.
3. If item 2 is real, is that I have to porting the force enter to bootloader mode by botton...
Hi!
I am working on NRF 52840 Controller and Soft Device Version 6.0.0. Coding using Keil IDE in C.
Also developing using Free RTOS.
According to the requirement I need...
Hi,
My development environment is sdk12.3 s132_3.0 pca10040 I want to increase the MTU size to 64 bytes in nus. I programmed as below, but there is no MTU size change. It...
I have been trying to configure a single shot timer as a low power alternative to nrf_delay_ms().
I have my timeout handler configured to do nothing and the timer is created...
