Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I'm currently trying to sniff the DH Key Exchange as specified in Spec 5.1 p.2446. I'm using the nRF51 Dongle as sniffer, the nRF52 DK as slave and the nRF52840...
Hi,
I am using two nRF52840 DK in which one of the board is flashed with light switch client and other one is flashed with light server and a nRF mesh app is used for provisioning...
Hi,
I see Nordic has recently released an updated software to do direct test mode (without the use of python or the old nRFGo studio). I am able to run the test code on...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) While upgrading over serial interface using DFU, whether UART needs...
Hi,
If you are interested I would to contribute to https://github.com/NordicSemiconductor/nRF-Sniffer-for-802.15.4 repository. On the python driver part. You could allow...
Hello
I'm doing a test that if it's possible to start ibeacon function when BLE is connected in nRF52840. so I merge ibeacon into HRM demo code and as you can in the following...
Hello ...
Our BLE peripheral product (nRF52810, SDK 15.3.0, SD 112 6.1.1) is relatively simple. iOS device (central) connects to peripheral. Data is exchanged between the...
Hi, i'm new to Nordic devices and i hope this topic hasn't already been treated. I'm triyng to debug an example application; after the first breakpoint, i loose the control...
Hi,
I try to set the TX power of the NRF52833 to the maximum possible power level, but somehow nothing seems to affect it.
I first tried to change it in the sdk_config...
In spec, 9160's PSM current is 4uA/3.7V.
However, When I use a same PSM code.
On our product. We measured is 4.5uA/3.7V and 5.5uA/3.7V. And on 9160DK, the consumption...
HI,
I'm trying to add some functions to my code, and the buttons interaction is one of them. I saw some posts and I think I did exactly like that but I can't get interaction...
So I was following the documentation. Installed everything successfully. And now I am trying to send the program to the nrf52840. However when I do ninja flash<program> I...
I've been trying to create a simple SPI to UART bridge starting with the peripheral template example from the nRF5 SDK 16. I want to read 5 bytes from uart, send them via...
I've reviewed the different PWM examples that include the low power PWM, PWM driver and the PWM library. What I'm looking for is a very simple solution to drive a bipolar...
Hi,
I'm wondering if the current nRF sniffer firmware (v3.0.0) can detect extended advertisements on arbitrary channels? Is it supported in the firmware? If so, can I use...
