Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I am testing the ble blinky example as it is from SDK v16.0.0. I am seeing a good amount of time(~340ms) from reset(pin reset) to advertise the first packet. I am keen...
So for this what I am trying to do is-
result = ((float_t)0x3F4040A3); NRF_LOG_INFO("My float number" NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(result));
But this is...
Hi
I have a strange phenomenon when using ANT proximity function.
Configuration: nRF52840, SDK15.2.0, softdevice S340 v6.1.1
The following initialization function of...
I've been using the USB HID Composite example along with the advice from this thread https://devzone.nordicsemi.com/f/nordic-q-a/38271/writing-words-to-usb-composite-keyboard...
Good day
I'm trying to run the ANT IO demo using two nRF52840 DKs. In order to do that I am trying to migrate the example from softdevice s212 to s340. I am currently using...
hi,
i want to connect 18 peripherals to a central. if iam changing NRF_SDH_BLE_CENTRAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT more than 8, all peripherals stop pairing...
Hi,
usbd_cdc_acm project implemented UART over usb, which is great. However it cannot send bytes from PC to DK board, only DK board back to PC.
In order to implement sending...
I use the SPIM to access a nand flash memory device. There are times, when I need to "free" the SPI bus allocated by the nRF52840, so that another CPU can access the memory...
I have been closely following this thread ( https://devzone.nordicsemi.com/f/nordic-q-a/52689/nrf9160-lte-sensor-gateway-on-thingy-91/217018 ) to provide support for the LTE...
Hello all,
I am using the NRF52810 board with SDK 14.2
I wanted to convert pca10040 to pca10040e file of buttonless dfu and secure bootloader .
I have gone through this...
Hi, I can read data with my laptop BLE as below.
Could anyone tell me where can I find the data layout doc? I want to figure out the data layout and dimension.
Thanks...
I've been having several issues with the nRF52840 so far:
Issue 1:
When trying to flash an nRF52840 with NCP firmware using a Segger JLink, I connected the SWDIO and...
Hi all,
I noticed an issue on the last release of the NRF Connect mobile app at least on Adroid devices.
It seems that every time I am trying to make a secure DFU (buttonless...
Hey everyone!
How often does PM write into FDS? On each connection? Or on each new bonding? PM has some kind of peer ranking so I suppose that it needs to write on each...
