Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
hello..
I'm actually working on nrf51822,i could complete the advertising part successfully("hello world")..NOW i want to add privacy feature which allows an advertiser to...
Hi there,
I am working on the SDK13 project template that I am modifying in order to install a vendor type uuid.
But my code crash on "advertising_init" and ble_advertising_init...
While using the secure bootloader image and test application works consistently using the development kit I have not been able to port the solution reliably for our custom...
hai
i am using mbed to program my nrf51822.i want to set the analog pin p6 as analog in in one situation and as a digital out in another situation. but i am unable to do...
Hello.
After executing the code below, the RAM was dropped and the program could not be written.
for(idx = 0; idx < 7; idx++)
{
NRF_POWER->RAM[idx].POWER = (POWER_RAM_POWER_S0POWER_Off...
I'm studing the project of ble_app_gls/PCA10040/SDK11.0/ ,I have got some questions about the RACP indication pending and retransmittion mechnism. In this project(File ble_gls...
enter code here Hi guys I have managed to program an example BLE_Serial program into the nrf51822 but I cannot see anything coming out from the TX and RX ? Please guide me...
I've tried to install nRF Connect v2.0 on both Win 7 and Win 10 systems, both running Avast Anti-virus (up to date). In both cases the antivirus gives a warning about IDP...
I have the Memory Manager module enabled in my custom sdk_config. Within the module, I have both of the following defined.
MEM_MANAGER_ENABLE_LOGS 0
ENABLE_DEBUG_LOG_SUPPORT...
Hello - Is the long range option programmable in BT 5.0? During the run time, is it possible to switch between high speed and long range mode dynamically depending on the...
I am specific about master as I have to connect two simultaneously(obviously to two different pins pair). Plz provide any code outline if you have, Thank you in Advance
Hi.
I would like upload firmware from Atmel microcontroller to nRF51822 with SD130.
I suppose that I have to use single_bank_serial_s130 in nRF51822AA, but what I have to...
Hi,
I'm trying to implement dfu bootloader over uart, not dfu bootloader over air.
Where can I find a reference source code of dfu bootloader over uart?
regards ...
Hi,
We have to find the battery life of a central device based on nRF52 (s132 v3 soft device)running with 800mAh battery. The device scans for a peripheral in every 5 sec...
Hi!
I am trying to measure the current profile of a pca10056 board using an oscilloscope. I cut SB40, as per instructions in the User Guide and powered it using only a...
