But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I'm unable to capture packets using the sniffer. Here are details regarding my set-up:
System: Debian 9.4 with kernel 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017...
Many of the pins in the assignments page of the documentation are designated as "Standard drive, low frequency only" and I cannot seem to find an explanation of what is considered...
I am trying to connect my android mobile with nRF 52DK using BLE on the NRF TOOLBOX android application. But the nRF 52DK is not recognize by the NRF TOOLBOX APP(proximity...
Hello,
we have a problem using the SAADC module with the low power mode, particularly after execution of the NRF_SAADC->TASKS_SAMPLE task.
Before taking a sample, the...
Hello,
I have some questions about ble_conn_params.c in SDK14.2
Question :
1. a. Why do you need to handle four ble conditions ?
b. Shouldn't just send connect parameters...
I hope to use a acceleration sensor with nRF51822 dev kit. So I should use three ADC input. I tested getting one ADC data using adc_simple example(Keil_v5/ARM/Pack/NordicSemiconductor...
We use nRF52832 ,when new android phone will connect to this device by mac,we cannot connect to it successfully,we must scan to find the device first,after found it,we can...
I want to t o ensure the stability of BLE connection for BLE frequence calibration,but i don't know how to get the nordic into the test mode and broadcast the empty packet...
https://devzone.nordicsemi.com/f/nordic-q-a/9231/ble_hci_conn_failed_to_be_established-0x3e-problem/34074#34074
I also encountered the same problem as this one. How to solve...
Hi,
I am working on my nrf52840 dongle and it looks really cool to me. I just found an issue that, when my dongle enter DFU mode using DFU trigger, I can not return to the...
Quick question:
What IDE are most developers using?
I've seen both Eclipse & Segger being discussed.
I'm interested in having the best support, most libraries & examples...
I'm getting errors on trying to program a custom board using the Laird BL654. We are verifying manufacturing results with an x-ray of a populated board tomorrow checking for...
Details
Hardware: Thingy52, nRF52840 Dev Board, Samsung Tab A running Android 5.1.1
Software: Windows 10, using GCC for compilation, Thingy52 SDK, Android-Nordic-Thingy...
I'd like to advertise indefinitely when my software application is in a certain state. Is there a mode that I can put the software in (using the aforementioned SDK) that will...
In infocenter we will have to define ***********
#define
nrf_drv_ppi_channel_assign nrfx_ppi_channel_assign
Macro for forwarding the new implementation....
