HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I am developing a product based on nrf52840 soc, I need to write a softdevice, program hex file, bootloader on the chip. when I want to select them all in the nrf...
I am trying to set up the LPS22HB sensor with an nRF52840. I am starting with the twi_sensor example(SDK16->examples->peripherals->twi_sensor) and adding the lps22hb example...
We have added custom HID firmware and are able to discover it on the Android Bluetooth Settings app. iOS fails to show the Bluetooth device on iOS Bluetooth Settings app....
Hi,
My task is..
Device will advertise for 20 seconds if there is no connection then it will go to sleep mode for 40 seconds. After 40 seconds it will wake up from sleep...
I have the nRF9160DK 0.8.3 which appears to align with the suggested schematic in "Objective Product Specification v0.7.1" I downloaded the hardware files form the Getting...
Hi,
To turn on and turn off the LED nrf SDK is using following code in sdk12.1.
#define LEDS_OFF(leds_mask) do { NRF_GPIO->OUTSET = (leds_mask) & (LEDS_MASK & LEDS_INV_MASK...
According to SIG's MESH Profile: "There is also a device key (DevKey), which is a special application key that is unique to each node, is known only to the node and a Configuration...
Hi,
I'm checking the e-sim functionnality with at_client firmware and LTE LInk Monitor. Once connectivity is proven to be successful, I can pursue my testings.
I was...
Hello!
I have questions.
I develop a central and peripheral devices at nrf52832.
I use SDK 15.3.0, s132 v6.1.1.
1.If I program Nordic's BLE peripheral sample into...
SDK ： nRF5_SDK_15.0.0_a53641a
example： nRF5_SDK_15.0.0_a53641a\examples\peripheral\twi_sensor
I didn't change anything. After build and download to the Nordic development...
Hello,
Im using pca10059 to scan for near beacons address and RSSI, but i also want to look for its battery level. (im using pca10056 to develop and debug)
I've found...
Hi.
I would like to measure the battery voltage using ADC in MCU. PCB has limited space, I consider to use the IC for this application.
The following is the LDO with...
Hello,
I am working on an IoT project using the Thingy 91 to send sensor data via Bluetooth to a remote device. Currently, I am trying to set up a simple beacon as shown...
