We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi All,
I'm using nrf52 PCA10040 v 0.9.0, with SDK11. No softdevice being used in this case.
While exploring using EasyDMA with the SPI peripheral, the example in sdk11...
Hi there,
this problem may extend the scope, as it relates the SPI slave device (atmel winc1500). When I run the SPI master example, I can see the data transmitted on oscilloscope...
Hi, I use S110 v8 in my application with DFU support. When DFU is triggered from application (by writing 0x0104 to DFU service control characteristic), then application fails...
Working on a project i want to update the nordic application (firmware) from other MCU, i am having some problem to compute the crc.
How to we calculate the crc of...
When I plug the nRF51822EK (PCA10024) in via USB while holding the reset button down, it mounts as "MBED LOADER" rather than "MBED". This page
developer.mbed.org/.../ ...
Hi,
I have a nordic chip (nrf2832) and I am trying to use it as a LWM2M client and register it to a LWM2M Server. I want to achieve this:
developer.nordicsemi.com/.....
I'm trying to update my SoftDevice with a bootloader, which is basically the same as the one in nRF5_SDK_11.0.0_89a8197. The image is saved in bank 0 and is validated by dfu_sd_image_validate...
This is my first DFU project, and so this may be super-obvious to all of you.
I am writing this here to help others, because it appears that there are others out there...
I have an mBed application that uses the S130 SoftDevice and polls data from a couple of other connected peripherals via I2C & SPI.
I use a Ticker object, which seems to...
Hello,
I use the example dfu_dual_bank_ble_132 in the nrf5x sdk 11 (PCA10040).
I have had my programe before the OTA, i will have a programme wich would update at any...
Hi all:
I stored some settings in flash in the address 0x00077000 and this address is got by the function of pstorage_register().
However this area will be erased by...
Hello there,
I've been trying to use embitz (the new version of emblocks) to program a nRF5188 but i always fail to compile the "ble_peripheral_hrs" exemple, i'm always...
Hi
I have a unit that is rather old and I want o update it to the latest softdevice.
In the unit there is a bootloader and softdevice version 6. Does anybody know if it...
I'm making progress, but still struggling to get the sample DFU built into NRF Toolbox to download successfully with my bootloader. Using hrs_dfu_s130_*.zip.
For this,...
