I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
i am working with nRF52840-DK which i received yesterday from shipment. so i want to eun the BLE peripheral application on that.
As we know if we want to run the BLE...
I see this quote in response to a question asking for examples on how to code a scan response
possibly not - but it's trivial - just encode the scan response in the same...
Hello,
I am using SES V4.5, SDK 15.2 and the "ble_app_blinky_c" and I was not able to see the programme log.
I tried setting up the file "sdk_config.h" to use the RTT...
Hello,
I'm starting to develop an application using the DK pca10040 and SDK 15.3. At first I have just adapted peripheral ble_app_uart example and incorporated fds functionality...
Hi,
This may be a simple question, but I've gone through the infocenter and am still a little confused. I'm designing a PCB on which I'd like to have an nrf52840 that can...
Hi,
I recently purchased the nRF9160DK but cannot connect to o2's LTE-M network using the iBasis SIM, following the instructions given here: https://www.nordicsemi.com/Software...
When I trap an error in app_error.c in app_error_save_and_stop,
I mostly get a filename, line number, and an error code that I can understand.
However, sometimes I...
We are looking for a freelancer who can help to build a simple Proof of Concept of a load cell (strain gauges) ADC (HX711?) and the nRF52 development kit (810).
Objectives...
Central and peripheral is pairing and bonded. Central scanning with whitelist, if Slave is not online, master scan with whitelist will enter error when more than 30 seconds...
I'm using whitelist when bonded, but I want delete bonded then connect to anther device,.
But when scan again, whitelist_load is error. Try delete whitelist at the same...
Extended corruption occurs if DMA transfers for commands and data originate from the same RAM bank.
It is avoided if transfer of command bytes and transfer of data bytes...
Hello,
I ran into this list recently: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2FnRF52840_ic_rev_sdk_sd_comp_matrix.html...
Hi,
I'm using two nrf52840 Dev Kits and am trying to test out the ATT_MTU throughput example with SDKv16. Whenever I program one of my boards I get repeated fatal error...
I am pulling my hair, literally , I just can't get this company !
I am working with 4 IDE's in parallel and none of them has this stupidity .
I right click->add a new...
