At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello I want to use MTU = 247 bytes. For 1M PHY, everything is working fine. When I set the coded PHY, there is a problem. I get the GATT event NRF_BLE_GATT_EVT_ATT_MTU_UPDATED...
I want to tested RF performance ，so i hope send cat-M 6RB@0 signal. For example, the circled part of the picture: ,it's send 6RB@22 signal。please tell me AT command.
Re: nRF52833DK, s113 and nRF5_SDK v16.0.0
It appears that nrf_sdh_freertos.c needs to be modified to support JUST_WORKS and LESC because the softdevice_task() in nrf_sdh_freertos...
Hi
I am working this tutorial . At the end of this, I copied and executed the contents of advertising_init() function but it became NRF_BREAKPOINT_COND.
When debugging...
I am trying to use the GPS from the Thingy:91. Due to the unavailability of Power Saving Mode (PSM) in roaming with my local provider, I am considering what options are available...
I am trying to see/set preprocessor options and they are not visible. I have seen the tutorial which says
project options >> code >> preprocessor should be the way to do...
Hello nordic, I have used the nrf24 before with ARM, and this go around its AVR, not that that changes much but looking for some help. I'm familiar with how this chip work...
Hello! We are designing an iPad app that will occasionally connect to our device over BLE. The app is kind of a maintenance/service app that will query various information...
I am trying to get the IEMI and HWID in my code. I was able to read the IEMI as a client ID using the following API.
nct_client_id_get(client_id_buf); printk("Client ID...
Hey there!
I´m developing an small wearable sensor based on the NRF52840 (SDK 15.0.0, S140 6.0.0) on a custom board. The sensor will log data on an external NAND flash and...
Dear Community;
I have a NRF9160 DK. I have flashed a program to it, and it works fine. The program connects to LTE every 10 minutes to send some data over HTTP. However...
I recently picked up an nRF52840 dongle and I cannot seem to get it to work properly on a very new Win10 machine. It does seem to work properly on my Mac however so I believe...
Hi,
I cant login to devzone from Firefox. But do not seem to have the problem using Chrome. I tried clearing cookies and site data. But couldn't login to the forum. It is...
SDK:nRF5_SDK_16.0.0_98a08e2
Hardware：52832QFAA
I refer to the code of ble_app_buttonless_dfu to port to ble_app_hrs_freertos but the following problems occur during the...
Hi,
I've been experimenting with the Mesh SDK (v3.2) on nRF52832 boards. After doing some end-to-end latency experiments, I've come up with some questions associated with...
